- 您現在的位置：買賣IC網 > PDF目錄377722 > LT3024EFE (LINEAR TECHNOLOGY CORP) Dual 100mA/500mA Low Dropout, Low Noise, Micropower Regulator PDF資料下載
參數資料
| 型號： | LT3024EFE |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Dual 100mA/500mA Low Dropout, Low Noise, Micropower Regulator |
| 中文描述： | DUAL OUTPUT, ADJUSTABLE POSITIVE LDO REGULATOR, PDSO16 |
| 封裝： | 4.40 MM, PLASTIC, TSSOP-16 |
| 文件頁數： | 14/16頁 |
| 文件大?。?/td> | 493K |
| 代理商： | LT3024EFE |
14
LT3024
3024f
The power dissipated by each output will be equal to:
I
OUT(MAX)
(V
IN(MAX)
– V
OUT
) + I
GND
(V
IN(MAX)
)
Where for Output 1:
I
OUT(MAX)
= 500mA
V
IN(MAX)
= 5V
I
GND
at (I
OUT
= 500mA, V
IN
= 5V) = 9mA
For Output 2:
I
OUT(MAX)
= 100mA
V
IN(MAX)
= 5V
I
GND
at (I
OUT
= 100mA, V
IN
= 5V) = 2mA
So for Output 1:
P = 500mA (5V – 3.3V) + 9mA (5V) = 0.90W
For Output 2:
P = 100mA (5V – 2.5V) + 2mA (5V) = 0.26W
The thermal resistance will be in the range of 35
°
C/W to
55
°
C/W depending on the copper area. So the junction
temperature rise above ambient will be approximately
equal to:
(0.90W + 0.26W) 50
°
C/W = 57.8
°
C
The maximum junction temperature will then be equal to
the maximum junction temperature rise above ambient
plus the maximum ambient temperature or:
T
JMAX
= 50
°
C + 57.8
°
C = 107.8
°
C
Protection Features
The LT3024 regulator incorporates several protection
features which make it ideal for use in battery-powered
circuits. In addition to the normal protection features
associated with monolithic regulators, such as current
limiting and thermal limiting, the device is protected
against reverse input voltages, reverse output voltages
and reverse voltages from output to input. The two regu-
lators have common V
IN
and GND pins and are thermally
coupled, however, the two outputs of the LT3024 operate
independently. They can be shut down independently and
a fault condition on one output will not affect the other
output electrically.
APPLICATIO
S I
FOR
ATIO
U
W
U
U
Current limit protection and thermal overload protection
are intended to protect the device against current overload
conditions at the output of the device. For normal opera-
tion, the junction temperature should not exceed 125
°
C.
The input of the device will withstand reverse voltages of
20V. Current flow into the device will be limited to less than
1mA (typically less than 100
μ
A) and no negative voltage
will appear at the output. The device will protect both itself
and the load. This provides protection against batteries
which can be plugged in backward.
The output of the LT3024 can be pulled below ground
without damaging the device. If the input is left open circuit
or grounded, the output can be pulled below ground by
20V. The output will act like an open circuit; no current will
flow out of the pin. If the input is powered by a voltage
source, the output will source the short-circuit current of
the device and will protect itself by thermal limiting. In this
case, grounding the SHDN1/SHDN2 pins will turn off the
device and stop the output from sourcing the short-circuit
current.
The ADJ pins can be pulled above or below ground by as
much as 7V without damaging the device. If the input is left
open circuit or grounded, the ADJ pins will act like an open
circuit when pulled below ground and like a large resistor
(typically 100k) in series with a diode when pulled above
ground.
In situations where the ADJ pins are connected to a
resistor divider that would pull the pins above their 7V
clamp voltage if the output is pulled high, the ADJ pin input
current must be limited to less than 5mA. For example, a
resistor divider is used to provide a regulated 1.5V output
from the 1.22V reference when the output is forced to 20V.
The top resistor of the resistor divider must be chosen to
limit the current into the ADJ pin to less than 5mA when the
ADJ pin is at 7V. The 13V difference between output and
ADJ pin divided by the 5mA maximum current into the ADJ
pin yields a minimum top resistor value of 2.6k.
相關PDF資料 |
PDF描述 |
|---|---|
| LT311H | Voltage Comparator |
| LT311AN8 | Voltage Comparator |
| LT311 | Voltage Comparator |
| LT311A | Voltage Comparator |
| LT311AH | Voltage Comparator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3024EFE#PBF | 功能描述:IC REG LDO ADJ .5A/.1A 16-TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:1 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:8V 輸入電壓:10.5 V ~ 23 V 電壓 - 壓降（標準）:1.7V @ 40mA 穩壓器數量:1 電流 - 輸出:100mA（最小值） 電流 - 限制（最?。?- 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOIC 包裝:剪切帶 (CT) 產品目錄頁面:1075 (CN2011-ZH PDF) 其它名稱:296-24390-1 |
| LT3024EFE#TR | 功能描述:IC REG LDO ADJ .5A/.1A 16TSSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:800 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:2.5V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.7V @ 4A 穩壓器數量:1 電流 - 輸出:4A 電流 - 限制（最小）:4.2A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263-5 包裝:帶卷 (TR) 其它名稱:AP1184K525L-13AP1184K525LDITR |
| LT3024EFE#TRPBF | 功能描述:IC REG LDO ADJ .5A/.1A 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 系列:- 標準包裝:800 系列:- 穩壓器拓撲結構:正，固定式 輸出電壓:2.5V 輸入電壓:最高 16V 電壓 - 壓降（標準）:0.7V @ 4A 穩壓器數量:1 電流 - 輸出:4A 電流 - 限制（最?。?4.2A 工作溫度:0°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:TO-263-6，D²Pak（5 引線+接片），TO-263BA 供應商設備封裝:TO-263-5 包裝:帶卷 (TR) 其它名稱:AP1184K525L-13AP1184K525LDITR |
| LT3024EFEPBF | 制造商:Linear Technology 功能描述:LT3024 dual adj 500/100mA LDO regulator |
| LT3024EFE-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 100mA/500mA Low Dropout, Low Noise,Micropower Regulator |
發布緊急采購，3分鐘左右您將得到回復。