- 您現在的位置：買賣IC網 > PDF目錄383289 > LT3420 (Linear Technology Corporation) Photoflash Capacitor Chargers with Automatic Refresh PDF資料下載
參數資料
| 型號： | LT3420 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Photoflash Capacitor Chargers with Automatic Refresh |
| 中文描述： | 照相閃光燈電容充電器，具有自動刷新 |
| 文件頁數： | 8/20頁 |
| 文件大小： | 368K |
| 代理商： | LT3420 |
LT3420/LT3420-1
8
3420fa
Overview
The following text focuses on the operation of the LT3420.
The operation of the LT3420-1 is nearly identical with the
differences discussed at the end of this section.
The LT3420 uses an adaptive on-time/off-time control
scheme to provide excellent efficiency and precise control
of switching currents. Please refer to Figure 3 for the fol-
lowing overview of the part’s operation. At any given instant,
the master latch determines which mode the LT3420 is in:
“charging” or “refresh”. In charging mode, the circuitry
enclosed by the smaller dashed box is enabled, providing
power to charge photoflash capacitor C1. The output volt-
age is monitored via the flyback pulse on the primary of the
transformer. When the target output voltage is reached, the
charging mode is terminated and the part enters the refresh
mode. In refresh mode, the power delivery block is disabled,
reducing quiescent current, while the refresh timer is en-
abled. The refresh timer simply generates a user program-
mable delay, after which the part reenters the charging
mode. Once in the charging mode, the LT3420 will again
provide power to the output until the target voltage is
reached. Figure 5 is an oscillograph photo showing both the
initial charging of the photoflash capacitor and the subse-
quent refresh action. The upper waveform is the output
voltage. The middle waveform is the voltage on the C
T
pin.
The lower waveform shows the input current. The mode of
the part is indicated below the photo.
The user can defeat the refresh timer and force the part
into charging mode by toggling the CHARGE pin
OPERATIOU
(high
→
low
→
high). The low to high transition on the
CHARGE pin fires a one-shot that sets the master latch,
putting the part in charging mode. Bringing CHARGE low
puts the part in shutdown. The refresh timer can be
programmed to wait indefinitely by simply grounding the
C
T
pin. In this configuration, the LT3420 will only reenter
the charging mode by toggling the CHARGE pin.
Power Delivery Block
The power delivery block consists of all circuitry enclosed
by the smaller dashed box in Figure 3. This circuit block
contains all elements needed for charging and output
voltage detection. To better understand the circuit opera-
tion, follow the subsequent description of one cycle of
operation and refer to Figure 6. Assume that initially there
is no current in the primary or secondary of the trans-
former, so the output of comparator A1 is low, while that
of A2 is high (note the small offset voltages at the inputs
of A1 and A2). The SR latch is thus set and the power NPN
switch, Q1, is turned on. Current increases linearly in the
primary of the transformer at a rate determined by the V
BAT
voltage and the primary inductance of the transformer. As
the current builds up, the voltage across the 14m
resistor increases. When this voltage exceeds the 20mV
offset voltage of A1, the output of A1 goes high, resetting
the SR latch and turning off Q1. The current needed to
reset the latch is approximately 1.4A (~20mV/14m
).
When Q1 turns off, the secondary side current quickly
jumps from zero current to the primary side current di-
vided by N (the turns ratio of transformer T1). In this ex-
ample, the peak secondary current is 116mA (1.4A/12).
Diode D1 now conducts, providing power to the output.
Since a positive voltage exists across the secondary wind-
ing of the transformer, the secondary current decreases
linearly at a rate determined by the secondary inductance
and the output voltage (neglecting the diode voltage drop).
When the secondary side current drops below 40mA
(10mV/0.25
), the output of A2 goes high, setting the SR
latch and turning on Q1. The initial primary current is sim-
ply the minimum secondary current times N, in this case
0.48A (40mA 12) . Q1 will now remain on until the pri-
mary current again reaches 1.4A. This cycle of operation
repeats itself, automatically adjusting the On and Off times
Figure 5. Demonstrating 3 Operating Modes of LT3420:
Shutdown, Charging and Refresh of Photoflash Capacitor
V
100V/DIV
MODE
I
IN
1A/DIV
V
CT
1V/DIV
1s/DIV
3420 F05
SHUTDOWN
CHARGING
REFRESH
相關PDF資料 |
PDF描述 |
|---|---|
| LT3526 | Regulating Pulse Width Modulator |
| LT3526J | Regulating Pulse Width Modulator |
| LT3526N | Regulating Pulse Width Modulator |
| LT1526 | Octal Bus Transceivers 20-SOIC 0 to 70 |
| LT1526J | Octal Bus Transceivers 20-SOIC 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3420-1 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Photoflash Capacitor Chargers with Automatic Refresh |
| LT3420EDD#PBF | 功能描述:IC PHOTOFLASH CAP CHARGER 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
| LT3420EDD#TR | 制造商:Linear Technology 功能描述:SP-SWREG/Monolithic, Photoflash Capacitor Charger w/ Automatic Top-Off |
| LT3420EDD#TRPBF | 功能描述:IC PHOTOFLASH CAP CHARGER 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 應用說明:Ultrasound Imaging Systems Application Note 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:37 系列:- 應用:醫(yī)療用超聲波成像，聲納 電流 - 電源:- 電源電壓:2.37 V ~ 6 V 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:56-WFQFN 裸露焊盤 供應商設備封裝:56-TQFN-EP（8x8） 包裝:管件 |
| LT3420EDD-1#PBF | 功能描述:IC PHOTOFLASH CAP CHARGER 10-DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 電源管理 - 專用 系列:- 標準包裝:1 系列:- 應用:手持/移動設備 電流 - 電源:- 電源電壓:3 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-LLP-EP（4x4） 包裝:Digi-Reel® 配用:LP3905SD-30EV-ND - BOARD EVALUATION LP3905SD-30 其它名稱:LP3905SD-30DKR |
發(fā)布緊急采購，3分鐘左右您將得到回復。