- 您現在的位置：買賣IC網 > PDF目錄377723 > LT3437EDD (LINEAR TECHNOLOGY CORP) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | LT3437EDD |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 0.9 A SWITCHING REGULATOR, 240 kHz SWITCHING FREQ-MAX, PDSO10 |
| 封裝： | 3 X 3 MM, 0.75 MM HEIGHT, PLASTIC, MO-229WEED-2, DFN-10 |
| 文件頁數： | 16/24頁 |
| 文件大?。?/td> | 523K |
| 代理商： | LT3437EDD |
LT3437
16
3437f
APPLICATIOU
The use of so-called “ultrafast” recovery diodes is gener-
ally not recommended. When operating in continuous
mode, the reverse recovery time exhibited by “ultrafast”
diodes will result in a slingshot type effect. The power
internal switch will ramp up V
IN
current into the diode in an
attempt to get it to recover. When the diode has finally
turned off, some tens of nanoseconds later, the V
SW
node
voltage ramps up at an extremely high dV/dt, perhaps 5V
to even 10V/ns! With real world lead inductances, the V
SW
node can easily overshoot the V
IN
rail. This can result in
poor RFI behavior, and if the overshoot is severe enough,
damage the IC itself.
W
U
U
BOOST PIN
For most applications, the boost components are a 0.1
μ
F
capacitor and a BAS21 diode. The anode is typically
connected to the regulated output voltage, to generate a
voltage approximately V
OUT
above V
IN
to drive the output
stage (Figure 6a). However, the output stage discharges
the boost capacitor during the on time of the switch. The
output driver requires at least 2.5V of headroom through-
out this period to keep the switch fully saturated. If the
output voltage is less than 3.3V, it is recommended that an
alternate boost supply is used. The boost diode can be
connected to the input (Figure 6b), but care must be taken
to prevent the boost voltage (V
BOOST
= V
IN
2) from
exceeding the BOOST pin absolute maximum rating. The
additional voltage across the switch driver also increases
power loss and reduces efficiency. If available, an inde-
pendent supply can be used to generate the required
BOOST voltage (Figure 6c). Tying BOOST to V
IN
or an
independent supply may reduce efficiency, but it will
reduce the minimum V
IN
required to start-up with light
loads. If the generated BOOST voltage dissipates too
much power at maximum load, the BOOST voltage the
LT3437 sees can be reduced by placing a Zener diode in
series with the BOOST diode (Figure 6a option).
A 0.1
μ
F boost capacitor is recommended for most appli-
cations. Almost any type of film or ceramic capacitor is
suitable, but the ESR should be <1
to ensure it can be
fully recharged during the off time of the switch. The
capacitor value is derived from worst-case conditions of
4700ns on time, 11mA boost current and 0.7V discharge
ripple. The boost capacitor value could be reduced under
less demanding conditions, but this will not improve
circuit operation or efficiency. Under low input voltage and
low load conditions, a higher value capacitor will reduce
discharge ripple and improve start-up operation.
SHUTDOWN FUNCTION AND UNDERVOLTAGE
LOCKOUT
The SHDN pin on the LT3437 controls the operation of the
IC. When the voltage on the SHDN pin is below the 1.2V
shutdown threshold, the LT3437 is placed in a “zero”
supply current state. Driving the SHDN pin above the
shutdown threshold enables normal operation. The SHDN
pin has an internal sink current with a typical value of 5
μ
A.
In addition to the shutdown feature, the LT3437 has an
undervoltage lockout function. When the input voltage is
BOOST
LT3437
GND
V
BOOST
– V
= V
OUT
V
BOOST(MAX)
= V
IN
+ V
OUT
V
IN
V
OUT
OPTIONAL
(6a)
V
IN
SW
BOOST
LT3437
GND
V
BOOST
– V
SW
= V
DC
V
BOOST(MAX)
= V
DC
+ V
IN
V
IN
V
DC
D
SS
3437 F06
V
OUT
(6c)
V
IN
SW
BOOST
LT3437
GND
V
BOOST
– V
SW
= V
IN
V
BOOST(MAX)
= 2V
IN
V
IN
V
OUT
(6b)
V
IN
SW
Figure 6. BOOST Pin Configurations
相關PDF資料 |
PDF描述 |
|---|---|
| LT3437 | Panels; For Use With:EUROCARD Subracks RoHS Compliant: Yes |
| LT3437IFE | MOSFET N-CHANNEL 100V SOT323 |
| LT3437EFE | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LT3460 | 1.3MHz Step-Up DC/DC Converter in SC70 and ThinSOT |
| LT3460ESC6 | 1.3MHz Step-Up DC/DC Converter in SC70 and ThinSOT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3437EDD#PBF | 功能描述:IC REG BUCK ADJ 0.5A 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 設計資源:Design Support Tool 標準包裝:1 系列:- 類型:升壓（升壓） 輸出類型:固定 輸出數:1 輸出電壓:3V 輸入電壓:0.75 V ~ 2 V PWM 型:- 頻率 - 開關:- 電流 - 輸出:100mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-5 細型，TSOT-23-5 包裝:剪切帶 (CT) 供應商設備封裝:TSOT-23-5 其它名稱:AS1323-BTTT-30CT |
| LT3437EDD#TRPBF | 功能描述:IC REG BUCK ADJ 0.5A 10DFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:2,500 系列:- 類型:升壓（升壓） 輸出類型:可調式 輸出數:1 輸出電壓:1.24 V ~ 30 V 輸入電壓:1.5 V ~ 12 V PWM 型:電流模式，混合 頻率 - 開關:600kHz 電流 - 輸出:500mA 同步整流器:無 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 包裝:帶卷 (TR) 供應商設備封裝:8-SOIC |
| LT3437EFE | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 3.3V to 60V 16-Pin TSSOP EP |
| LT3437EFE#PBF | 功能描述:IC REG BUCK ADJ 0.5A 16TSSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 開關穩壓器 系列:- 標準包裝:250 系列:- 類型:降壓（降壓） 輸出類型:固定 輸出數:1 輸出電壓:1.2V 輸入電壓:2.05 V ~ 6 V PWM 型:電壓模式 頻率 - 開關:2MHz 電流 - 輸出:500mA 同步整流器:是 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:6-UFDFN 包裝:帶卷 (TR) 供應商設備封裝:6-SON（1.45x1） 產品目錄頁面:1032 (CN2011-ZH PDF) 其它名稱:296-25628-2 |
| LT3437EFE#TR | 制造商:Linear Technology 功能描述:Conv DC-DC Single Step Down 3.3V to 60V 16-Pin TSSOP EP T/R |
發布緊急采購，3分鐘左右您將得到回復。