參數資料
型號： LT3645HMSE#TRPBF
廠商： Linear Technology
文件頁數： 18/24頁
文件大小： 300K
描述： IC REG DL BUCK/LINEAR 12-MSOP
標準包裝： 2,500
拓?fù)洌?/td> 降壓（降壓）（1），線性（LDO）（1）
功能： 車載
輸出數： 2
頻率 - 開關： 750kHz
電壓/電流 - 輸出 1： 0.8 V ~ 16 V，500mA
電壓/電流 - 輸出 2： 0.8 V ~ 8 V，200mA
帶 LED 驅動器： 無
帶監控器： 無
帶序列發生器： 無
電源電壓： 3.6 V ~ 36 V
工作溫度： -40°C ~ 150°C
安裝類型： 表面貼裝
封裝/外殼： 12-TSSOP （0.118"，3.00mm 寬）裸露焊盤
供應商設備封裝： 12-MSOP，裸露焊盤
包裝： 帶卷 (TR)
LT3645
18
3645f
APPLICATIONS INFORMATION
P1 has a  nite on-resistance which will result in power
dissipation and some loss in ef ciency. For higher buck
output voltage applications, a smaller PFET may be used
since the gate drive will be higher.
PCB Layout
For proper operation and minimum EMI, care must be taken
during printed circuit board layout. Figure 13 shows the
recommended component placement with trace, ground
plane, and via locations.
Note that large, switched currents  ow in the LT3645s V
IN
 
and SW pins, the catch diode (D1), and the input capacitor
(C1). The loop formed by these components should be as
small as possible and tied to system ground in only one
place. These components, along with the inductor and
output capacitor, should be placed on the same side of the
circuit board, and their connections should be made on
that layer. Place a local, unbroken ground system ground in
only one place. These components, along with the inductor
and output capacitor, should be placed on the same side
of the circuit board, and their connections should be made
on that layer. Place a local, unbroken ground plane below
these components, and tie this ground plane to system
ground at one location (ideally at the ground terminal of
the output capacitor C1). The SW and BOOST nodes should
be kept as small as possible. Finally, keep the FB nodes
small so that the ground pin and ground traces will shield
them from the SW and BOOST nodes. Include vias near
the exposed GND pad of the LT3645 to help remove heat
from the LT3645 to the ground plane.
High Temperature Considerations
The die temperature of the LT3645 must be lower than
the maximum rating of 125癈 (150癈 for H-grade). This
is generally not a concern unless the ambient tempera-
ture is above 85癈. For higher temperatures, extra care
should be taken in the layout of the circuit to ensure good
heat sinking at the LT3645. The maximum load current
should be derated as the ambient temperature approaches
125癈. The die temperature is calculated by multiplying the
LT3645 power dissipation by the thermal resistance from
junction to ambient. Power dissipation within the LT3645
can be estimated by calculating the total power loss from
an ef ciency measurement and subtracting the catch diode
loss. The resulting temperature rise at full load is nearly
independent of input voltage. Thermal resistance depends
upon the layout of the circuit board, but 68癈/W is typical
for the QFN (UD) package, and 40癈/W is typical for the
MSE package. Thermal shutdown will turn off the Buck
and LDO when the die temperature exceeds 160癈, but
it is not a warrant to allow operation at die temperatures
exceeding 125癈 (150癈 for H-grade).
Other Linear Technology Publications
Application Notes 19, 35, and 44 contain more detailed
descriptions and design information for step-down regu-
lators and other switching regulators. The LT1376 data
sheet has an extensive discussion of output ripple, loop
compensation, and stability testing. Design Note 318
shows how to generate a bipolar output supply using a
step-down regulator.
Figure 13.
3645 F13
C3
C2
D1
DA
L1
SW
C4
C1
C5
R1
R3
MAIN PCB
BOARD
POWER
R2
FB1
BOOST
FB2
R4
OUT1
V
IN
V
IN
V
CC2
EN/UVLO
NPG EN2
OUT2
VIA TO LOCAL GROUND PLANE
OUTLINE OF LOCAL GROUND PLANE
+
相關PDF資料
PDF描述
LT3694IFE-1#TRPBF IC REG TRPL BUCK/LINEAR 20TSSOP
LT4220IGN#TR IC CTLR HOTSWAP DUAL 16-SSOP
LT4250LCN8 IC CONTRLR HOT SWAP NEG 48V 8DIP
LT4254CGN IC CTRLR HOTSWAP POSVOLT 16SSOP
LT4256-1IS8#TRPBF IC CTRLR HOTSWAP HV LATCH 8SOIC
相關代理商/技術參數
參數描述
LT3645IMSE#PBF 功能描述:IC REG DL BUCK/LINEAR 12-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:*
LT3645IMSE#TRPBF 功能描述:IC REG DL BUCK/LINEAR 12-MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:*
LT3645IUD#PBF 功能描述:IC REG DL BUCK/LINEAR 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:*
LT3645IUD#TRPBF 功能描述:IC REG DL BUCK/LINEAR 16-QFN RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - 線性 + 切換式 系列:- 標準包裝:2,500 系列:- 拓?fù)?降壓（降壓）同步（3），線性（LDO）（2） 功能:任何功能 輸出數:5 頻率 - 開關:300kHz 電壓/電流 - 輸出 1:控制器 電壓/電流 - 輸出 2:控制器 電壓/電流 - 輸出 3:控制器 帶 LED 驅動器:無 帶監控器:無 帶序列發生器:是 電源電壓:5.6 V ~ 24 V 工作溫度:-40°C ~ 85°C 安裝類型:* 封裝/外殼:* 供應商設備封裝:* 包裝:*
LT3650 制造商:LINER 制造商全稱:Linear Technology 功能描述:High Voltage High Current Controller for Battery Charging and Power Management
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*