- 您現在的位置：買賣IC網 > PDF目錄44987 > LT3748HMS#PBF (LINEAR TECHNOLOGY CORP) SWITCHING CONTROLLER, PDSO12 PDF資料下載
參數資料
| 型號： | LT3748HMS#PBF |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING CONTROLLER, PDSO12 |
| 封裝： | LEAD FREE, PLASTIC, MSOP-16/12 |
| 文件頁數： | 3/30頁 |
| 文件大?。?/td> | 284K |
| 代理商： | LT3748HMS#PBF |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
LT3748
11
3748fa
APPLICATIONS INFORMATION
Minimum Primary Inductance Requirements
The LT3748 obtains output voltage information from the
external MOSFET drain voltage when the secondary winding
conducts current. The sampling circuitry needs a minimum
of 400ns to settle and sample the output voltage while the
MOSFET switch is off. This required settle and sample
time is controlled by external components independent of
the minimum off-time of the GATE pin as specified in the
Electrical Characteristics table. The electrical specification
minimum off-time is based on an internal timer and acts
as a maximum frequency clamp. The following equation
gives the minimum value for primary-side magnetizing
inductance:
LPRI ≥
VOUT + VF(DIODE)
() RSENSE tSETTLE(MIN) NPS
VSENSE(MIN)
VSENSE(MIN) = 15mV
tSETTLE(MIN) = 400ns
NPS = Ratio of primary windings to secondary windings
In addition to the primary inductance requirement for
minimum settling and sampling time, the LT3748 has
internal circuit constraints that prevent it from setting the
GATE node high for shorter than approximately 250ns.
If the inductor current exceeds the desired current limit
during that time oscillation may occur at the output as
the current control loop will lose its ability to regulate.
Therefore, the following equation relating to maximum
input voltage must also be followed in selecting primary-
side magnetizing inductance:
LPRI ≥
VIN(MAX)RSENSE tON(MIN)
VSENSE(MIN)
tON(MIN) = 250ns
The last constraint on minimum inductance value would
relate to minimum full-load operating frequency, fMIN, and
is derived from fSW = 1/(tON + tOFF):
LPRI≤VIN(MIN)(VOUT+VF(DIODE))NPS/(fSW(MIN)ILIM
((VOUT + VF(DIODE)) NPS + VIN(MIN)))
The minimum operating frequency may be lower than
the calculated number due to delays in detecting current
limit and detecting boundary mode that are specific to
each application.
Output Power
Because the MOSFET power switch is located outside the
LT3748, the maximum output power is primarily limited
by external components. Output power limitations can
be separated into three categories—voltage limitations,
current limitations and thermal limitations.
The voltage limitations in a flyback design are primarily
the MOSFET switch VDS(MAX) and the output diode re-
verse-bias rating. Increasing the voltage rating of either
component will typically decrease application efficiency if
all else is equal and the voltage requirements on each of
those components will be directly related to the windings
ratio of the transformer, the input and output voltages
and the use of any additional snubbing components.
The MOSFET VDS(MAX) must theoretically be higher than
VIN(MAX) + (VOUT NPS) and the output diode reverse bias
must be higher than VOUT + (VIN(MAX)/NPS), though leak-
age inductance spikes on both the drain of the MOSFET
and the anode of the output diode may more than double
that requirement (see section on leakage inductance for
more details on snubbers). Figure 1 illustrates the effect
on available output power for several MOSFET voltage
ratings while continuously maximizing windings ratio
for input voltage with a fixed MOSFET current limit and
output voltage. Increasing the MOSFET rating increases
the possible windings ratio and or maximum input voltage
and can increase the available output power for a given
application. Both figures assume no leakage inductance
and high efficiency.
INPUT VOLTAGE (V)
0
MAXIMUM
OUTPUT
POWER
(W)
30
40
50
80
3748 F01
20
10
0
20
40
60
100
VDS = 200V
VDS = 150V
VDS = 100V
Figure 1. Maximum Output Power at 12VOUT with a
3A ILIM and Maximum VDS = 100V, 150V, 200V
相關PDF資料 |
PDF描述 |
|---|---|
| LT3758HMSE#TRPBF | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT3758MPMSE#PBF | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT3758HMSE#PBF | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT3758MPMSE#TRPBF | SWITCHING REGULATOR, 1000 kHz SWITCHING FREQ-MAX, PDSO10 |
| LT3782IFE#TR | 4 A SWITCHING CONTROLLER, 533 kHz SWITCHING FREQ-MAX, PDSO28 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT3748HMSTRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:100V Isolated Flyback Controller |
| LT3748IMS#PBF | 功能描述:IC REG CTRLR FLYBK ISO CM 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LT3748IMS#TRPBF | 功能描述:IC REG CTRLR FLYBK ISO CM 16MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LT3748IMSPBF | 制造商:Linear Technology 功能描述:100V Isolated Flyback Controller MSOP16 |
| LT3748IMSTRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:100V Isolated Flyback Controller |
發布緊急采購，3分鐘左右您將得到回復。