- 您現在的位置：買賣IC網 > PDF目錄44987 > LT4356HMS-3 (LINEAR TECHNOLOGY CORP) SPECIALTY ANALOG CIRCUIT, PDSO10 PDF資料下載
參數資料
| 型號： | LT4356HMS-3 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PDSO10 |
| 封裝： | PLASTIC, MSOP-10 |
| 文件頁數： | 22/24頁 |
| 文件大?。?/td> | 231K |
| 代理商： | LT4356HMS-3 |
LT4356-3
7
43563fa
PIN FUNCTIONS
AOUT (DFN and SO Packages Only): Amplier Output.
Open collector output of the auxiliary amplier. It is capable
of sinking up to 2mA from 80V. The negative input of the
amplier is internally connected to a 1.25V reference.
EN: Open-Collector Enable Output. The EN pin goes high
impedance when the voltage at the OUT pin is above (VCC
– 0.7V), indicating the external MOSFET is fully on. The
state of the pin is latched until the OUT pin voltage resets
at below 0.5V and goes back up above 2V. The internal
NPN is capable of sinking up to 3mA of current from 80V
to drive an LED or opto-coupler.
Exposed Pad: Exposed pad may be left open or connected
to device ground (GND).
FB: Voltage Regulator Feedback Input. Connect this pin
to the center tap of the output resistive divider connected
between the OUT pin and ground. During an overvoltage
condition, the GATE pin is servoed to maintain a 1.25V
threshold at the FB pin. This pin is clamped internally to
7V. Tie to GND to disable the OV clamp.
FLT: Open-Collector Fault Output. This pin pulls low
after the voltage at the TMR pin has reached the fault
threshold of 1.25V. It indicates the pass transistor is
about to turn off because either the supply voltage has
stayed at an elevated level for an extended period of
time (voltage fault) or the device is in an overcurrent
condition (current fault). The internal NPN is capable of
sinking up to 3mA of current from 80V to drive an LED or
opto-coupler.
GATE: N-Channel MOSFET Gate Drive Output. The GATE pin
is pulled up by an internal charge pump current source and
clamped to 14V above the OUT pin. Both voltage and cur-
rent ampliers control the GATE pin to regulate the output
voltage and limit the current through the MOSFET.
GND: Device Ground.
IN+ (DFN and SO Packages Only):
Positive Input of the
Auxiliary Amplier. This amplier can be used as a level
detection comparator with external hysteresis or linear
regulator controlling an external PNP transistor. This pin is
clamped internally to 7V. Connect to ground if unused.
OUT: Output Voltage Sense Input. This pin senses the
voltage at the source of the N-channel MOSFET and sets
the fault timer current. When the OUT pin voltage reaches
0.7V away from VCC, the EN pin goes high impedance.
SHDN: Shutdown Control Input. The LT4356-3 can be
shut down to a low current mode by pulling the SHDN
pin below the shutdown threshold of 0.4V. All functions,
including the spare amplier, are turned off. Pull this pin
above 1.7V or disconnect it and allow the internal current
source to turn the part back on. After GATE pin pulls low
due to fault time out, the part can be restarted by pull-
ing the SHDN pin low for at least 100μs and pulled high
with a slew rate faster than 10V/ms. The leakage current
to ground at the pin should be limited to no more than
1μA if no pull up device is used to turn the part on. The
SHDN pin can be pulled up to 100V or below GND by 60V
without damage.
SNS: Current Sense Input. Connect this pin to the output of
the current sense resistor. The current limit circuit controls
the GATE pin to limit the sense voltage between VCC and
SNS pins to 50mV. At the same time the sense amplier
also starts a current source to charge up the TMR pin.
This pin can be pulled below GND by up to 60V, though
the voltage difference with the VCC pin must be limited to
less than 30V. Connect to VCC if unused.
TMR: Fault Timer Input. Connect a capacitor between this
pin and ground to set the times for early warning and fault
periods. The current charging up this pin during fault
conditions depends on the voltage difference between the
VCC and OUT pins. When VTMR reaches 1.25V, the FLT pin
pulls low to indicate the detection of a fault condition. If
the condition persists, the pass transistor turns off when
VTMR reaches the threshold of 1.35V. The GATE pin remains
low even after the fault condition has disappeared and the
voltage at the TMR pin has reached 0.5V.
VCC: Positive Supply Voltage Input. The positive supply
input ranges from 4V to 80V for normal operation. It
can also be pulled below ground potential by up to 60V
during a reverse battery condition, without damaging the
part. The supply current is reduced to 7μA with all the
functional blocks off.
相關PDF資料 |
PDF描述 |
|---|---|
| LT4356CDE-3#TR | SPECIALTY ANALOG CIRCUIT, PDSO12 |
| LT4356IS-3#TR | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| LT4356HS-3#TRPBF | SPECIALTY ANALOG CIRCUIT, PDSO16 |
| LT4356IDE-3#TR | SPECIALTY ANALOG CIRCUIT, PDSO12 |
| LT4356HDE-3#PBF | SPECIALTY ANALOG CIRCUIT, PDSO12 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT4356HMS-3#PBF | 功能描述:IC REG OVP W/LATCHOFF 10-MSOP RoHS:是 類別:過電壓，電流，溫度裝置 >> 電涌抑制 IC 系列:- 產品培訓模塊:LT4356 Surge Stopper 產品目錄繪圖:LT4356 Output Graph LT4356 Series 10-MSOP 標準包裝:2,500 系列:- 電壓 - 工作:4 ~ 80V 電壓 - 箝位:27V，可調 技術:混合技術 功率（瓦特）:- 電路數:1 應用:自動 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:帶卷 (TR) 配用:DC1018B-C-ND - DEMO BOARD FOR LT4356-3DC1018B-B-ND - DEMO BOARD FOR LT4356-2DC1018B-A-ND - DEMO BOARD FOR LT4356-1 |
| LT4356HMS-3#PBF | 制造商:Linear Technology 功能描述:HOT SWAP CONTROLLER IC |
| LT4356HMS-3#TRPBF | 功能描述:IC REG OVP FAULT TIMER 10MSOP RoHS:是 類別:過電壓，電流，溫度裝置 >> 電涌抑制 IC 系列:- 產品培訓模塊:LT4356 Surge Stopper 產品目錄繪圖:LT4356 Output Graph LT4356 Series 10-MSOP 標準包裝:2,500 系列:- 電壓 - 工作:4 ~ 80V 電壓 - 箝位:27V，可調 技術:混合技術 功率（瓦特）:- 電路數:1 應用:自動 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:帶卷 (TR) 配用:DC1018B-C-ND - DEMO BOARD FOR LT4356-3DC1018B-B-ND - DEMO BOARD FOR LT4356-2DC1018B-A-ND - DEMO BOARD FOR LT4356-1 |
| LT4356HMS-3PBF | 制造商:Linear Technology 功能描述:Surge Protection Adj Regulator 4-80V 7uA |
| LT4356HS-1#PBF | 功能描述:IC SURGE STOPPER ADJ 16-SOIC RoHS:是 類別:過電壓，電流，溫度裝置 >> 電涌抑制 IC 系列:- 產品培訓模塊:LT4356 Surge Stopper 產品目錄繪圖:LT4356 Output Graph LT4356 Series 10-MSOP 標準包裝:2,500 系列:- 電壓 - 工作:4 ~ 80V 電壓 - 箝位:27V，可調 技術:混合技術 功率（瓦特）:- 電路數:1 應用:自動 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:帶卷 (TR) 配用:DC1018B-C-ND - DEMO BOARD FOR LT4356-3DC1018B-B-ND - DEMO BOARD FOR LT4356-2DC1018B-A-ND - DEMO BOARD FOR LT4356-1 |
發布緊急采購，3分鐘左右您將得到回復。