- 您現在的位置：買賣IC網 > PDF目錄5285 > LT6211IMS (Linear Technology)IC AMP CURR FDBK DUAL R-R 10MSOP PDF資料下載
參數資料
| 型號： | LT6211IMS |
| 廠商： | Linear Technology |
| 文件頁數： | 5/18頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP CURR FDBK DUAL R-R 10MSOP |
| 標準包裝： | 50 |
| 放大器類型： | 電流反饋 |
| 電路數： | 2 |
| 輸出類型： | 滿擺幅 |
| 轉換速率： | 700 V/µs |
| -3db帶寬： | 200MHz |
| 電流 - 輸入偏壓： | 13.5µA |
| 電壓 - 輸入偏移： | 1000µV |
| 電流 - 電源： | 6mA |
| 電流 - 輸出 / 通道： | 75mA |
| 電壓 - 電源，單路/雙路(±)： | 3 V ~ 12 V，±1.5 V ~ 6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁
LT6210/LT6211
13
62101fc
applicaTions inForMaTion
Capacitive Loads
The LT6210/LT6211 are stable with any capacitive load.
Although peaking and overshoot may result in the AC
transientresponse,theamplifier’scompensationdecreases
bandwidthwithincreasingoutputcapacitiveloadtoensure
stability. To maintain a response with minimal peaking, the
feedbackresistorcanbeincreasedatthecostofbandwidth
as shown in the Typical Performance Characteristics.
Alternatively, a small resistor (5Ω to 35Ω) can be put in
series with the output to isolate the capacitive load from
theamplifieroutput.Thishastheadvantagethattheampli-
fier bandwidth is only reduced when the capacitive load
is present. The disadvantage of this technique is that the
gain is a function of the load resistance.
Power Supplies
The LT6210/LT6211 will operate on single supplies from
3V to 12V and on split supplies from ±1.5V to ±6V. If split
supplies of unequal absolute value are used, input offset
voltageandinvertinginputcurrentwillshiftfromthevalues
specifiedintheElectricalCharacteristicstable.Inputoffset
voltage will shift 2mV and inverting input current will shift
0.5A for each volt of supply mismatch.
Slew Rate
Unlike a traditional voltage feedback op amp, the slew rate
of a current feedback amplifier is not independent of the
amplifier gain configuration. In a current feedback ampli-
fier, both the input stage and the output stage have slew
rate limitations. In the inverting mode, and for gains of 2
or more in the noninverting mode, the signal amplitude
between the input pins is small and the overall slew rate
is that of the output stage. For gains less than 2 in the
noninverting mode, the overall slew rate is limited by the
input stage. The input slew rate of the LT6210/LT6211 on
±5V supplies with an RSET resistor of 20k (IS = 6mA) is
approximately 600V/s and is set by internal currents and
capacitances. The output slew rate is additionally con-
strained by the value of the feedback resistor and internal
capacitance. At a gain of 2 with 887Ω feedback and gain
resistors, ±5V supplies and the same biasing as above,
the output slew rate is typically 700V/s. Larger feedback
resistors, lower supply voltages and lower supply current
levelswillallreduceslewrate.Inputslewratessignificantly
exceeding the output slew capability can actually decrease
slew performance in a positive gain configuration; the
cleanest transient response will be obtained from input
signals with slew rates slower than 1000V/s.
Output Swing and Drive
The output stage of the LT6210/LT6211 consists of a pair
ofclass-ABbiasedcommonemittersthatenabletheoutput
to swing rail-to-rail. Since the amplifiers can potentially
deliveroutputcurrentswellbeyondthespecifiedminimum
short-circuit current, care should be taken not to short the
output of the device indefinitely. Attention must be paid to
keep the junction temperature of the IC below the absolute
maximum rating of 150°C if the output is used to drive
low impedance loads. See Note 5 for details. Additionally,
the output of the amplifier has reverse-biased ESD diodes
connected to each supply. If the output is forced beyond
eithersupply,largecurrentswillflowthroughthesediodes.
If the current is limited to 80mA or less, no damage to
the part will occur.
相關PDF資料 |
PDF描述 |
|---|---|
| 3410.0036.02 | FUSE MGA 125V 2.5A |
| LT1490ACMS8 | IC OPAMP DUAL R-R MCRPWR 8MSOP |
| LT1490AIN8#PBF | IC OPAMP DUAL R-R MCRPWR 8DIP |
| PPPC341LGBN-RC | CONN FEMALE 34POS .100" R/A GOLD |
| LT1490AIN8 | IC OPAMP DUAL R-R MCRPWR 8DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT6211IMS#PBF | 功能描述:IC AMP CURR FDBK DUAL R-R 10MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LT6211IMS#TR | 功能描述:IC AMP CURR FDBK DUAL R-R 10MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LT6211IMS#TRPBF | 功能描述:IC AMP CURR FDBK DUAL R-R 10MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:2,500 系列:- 放大器類型:通用 電路數:1 輸出類型:滿擺幅 轉換速率:0.11 V/µs 增益帶寬積:350kHz -3db帶寬:- 電流 - 輸入偏壓:4nA 電壓 - 輸入偏移:20µV 電流 - 電源:260µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):2.7 V ~ 36 V，±1.35 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SO 包裝:帶卷 (TR) |
| LT6220 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Single/Dual/Quad 60MHz, 20V/us, Low Power, Rail-to-Rail Input and Output Precision Op Amps |
| LT6220CS5 | 制造商:Linear Technology 功能描述:OP Amp Single GP R-R I/O ±6.3V/12.6V 5-Pin TSOT-23 |
發布緊急采購，3分鐘左右您將得到回復。