參數資料
| 型號： | LT6411IUD#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 15/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC DRVR/GAIN AMP 16-QFN |
| 標準包裝： | 2,500 |
| 放大器類型： | 通用 |
| 電路數： | 2 |
| 輸出類型： | 差分 |
| 轉換速率： | 3300 V/µs |
| -3db帶寬： | 650MHz |
| 電流 - 輸入偏壓： | 17µA |
| 電壓 - 輸入偏移： | 3000µV |
| 電流 - 電源： | 8mA |
| 電流 - 輸出 / 通道： | 105mA |
| 電壓 - 電源，單路/雙路(±)： | 4.5 V ~ 12 V，±2.25 V ~ 6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 16-QFN-EP（3x3） |
| 包裝： | 帶卷 (TR) |
LT6411
8
6411f
PIN FUNCTIONS
VEE (Pins 1, 2): Negative Supply Voltage. VEE pins are not
internally connected to each other and must all be con-
nected externally. Proper supply bypassing is necessary
for best performance. See the Applications Information
section.
VEE (Pins 3, 7): Negative Supply Voltage for Output Stage.
VEE pins are not internally connected to each other and
must all be connected externally. Proper supply bypassing
is necessary for best performance. See the Applications
Information section.
NC (Pin 4): This pin is not internally connected.
OUT2 (Pin 5): Output of Channel 2. The gain between the
input and the output of this channel is set by the connection
of the channel 2 input pins. See Table 1 in Applications
Information for details.
VCC (Pins 6, 9): Positive Supply Voltage for Output Stage.
VCC pins are not internally connected to each other and
must all be connected externally. Proper supply bypassing
is necessary for best performance. See the Applications
Information section.
OUT1 (Pin 8): Output of Channel 1. The gain between the
input and the output of this channel is set by the connection
of the channel 1 input pins. See Table 1 in Applications
Information for details.
VCC (Pin 10): Positive Supply Voltage. VCC pins are not
internally connected to each other and must all be con-
nected externally. Proper supply bypassing is necessary
for best performance. See the Applications Information
section.
EN (Pin 11): Enable Control Pin. An internal pull-up resis-
tor of 46k will turn the part off if the pin is allowed to oat
and denes the pin’s impedance. When the pin is pulled
low, the part is enabled.
DGND (Pin 12): Digital Ground Reference for Enable Pin.
This pin is normally connected to ground.
IN1+ (Pin 13): Channel 1 Positive Input. This pin has a
nominal impedance of 400k
Ωanddoesnothaveaninternal
termination resistor.
IN1– (Pin 14): This pin connects to the internal resistor
network of the channel 1 amplier, connecting by a 370
Ω
resistor to the inverting input.
IN2– (Pin 15): This pin connects to the internal resistor
network of the channel 2 amplier, connecting by a 370
Ω
resistor to the inverting input.
IN2+ (Pin 16): Channel 2 Positive Input. This pin has a
nominal impedance of 400k
Ωanddoesnothaveaninternal
termination resistor.
Exposed Pad (Pin 17): The pad is internally connected to
VEE (Pin 1). If split supplies are used, do not tie the pad
to ground.
相關PDF資料 |
PDF描述 |
|---|---|
| SSQ-146-02-S-S-RA | CONN RCPT .100" 46POS R/A SGL AU |
| SSQ-147-02-S-S-RA | CONN RCPT .100" 47POS R/A SGL AU |
| 10-89-7762 | CONN HDR DUAL 76POS .100 SRT AU |
| SSQ-148-02-S-S-RA | CONN RCPT .100" 48POS R/A SGL AU |
| SSQ-149-02-S-S-RA | CONN RCPT .100" 49POS R/A SGL AU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LT6412 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UNDERSTANDING THE SUBJECT IS CUSTOMER SERVICE |
| LT6413 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UNDERSTANDING THE SUBJECT IS CUSTOMER SERVICE |
| LT6414 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:UNDERSTANDING THE SUBJECT IS CUSTOMER SERVICE |
| LT64H-SERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
| LT64HXX-SERIES | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Optoelectronic |
發(fā)布緊急采購，3分鐘左右您將得到回復。