參數資料
型號: LTC1046M
廠商: Linear Technology Corporation
英文描述: “Inductorless” 5V to + 5V Converter
中文描述: “電感”5V至5V的轉換器
文件頁數: 6/12頁
文件大?。?/td> 172K
代理商: LTC1046M
LTC1046
6
U
S
A
By connecting the BOOST (Pin 1) to V
+
, the charge and
discharge current is increased and, hence, the frequency
is increased by approximately three times. Increasing the
frequency will decrease output impedance and ripple for
higher load currents.
O
PPLICATI
U
U
Loading Pin 7 with more capacitance will lower the fre-
quency. Using the BOOST pin in conjunction with external
capacitance on Pin 7 allows user selection of the fre-
quency over a wide range.
Driving the LTC1046 from an external frequency source
can be easily achieved by driving Pin 7 and leaving the
BOOST pin open, as shown in Figure 6. The output current
from Pin 7 is small, typically 15
μ
A, so a logic gate is
capable of driving this current. The choice of using a CMOS
logic gate is best because it can operate over a wide supply
voltage range (3V to 15V) and has enough voltage swing
to drive the internal Schmitt trigger shown in Figure 5. For
5V applications, a TTL logic gate can be used by simply
adding an external pull-up resistor (see Figure 6).
Capacitor Selection
While the exact values of C
IN
and C
OUT
are noncritical,
good quality, low ESR capacitors such as solid tantalum
are necessary to minimize voltage losses at high currents.
For C
IN
the effect of the ESR of the capacitor will be
multiplied by four, due to the fact that switch currents are
approximately two times higher than output current, and
losses will occur on both the charge and discharge cycle.
This means that using a capacitor with 1
of ESR for C
IN
will have the same effect as increasing the output imped-
ance of the LTC1046 by 4
. This represents a significant
increase in the voltage losses. For C
OUT
the effect of ESR
is less dramatic. C
OUT
is alternately charged and dis-
charged at a current approximately equal to the output
current, and the ESR of the capacitor will cause a step
function to occur, in the output ripple, at the switch
transitions. This step function will degrade the output
regulation for changes in output load current, and should
be avoided. Realizing that large value tantalum capacitors
can be expensive, a technique that can be used is to
parallel a smaller tantalum capacitor with a large alumi-
num electrolytic capacitor to gain both low ESR and
reasonable cost. Where physical size is a concern some
of the newer chip type surface mount tantalum capacitors
can be used. These capacitors are normally rated at
working voltages in the 10V to 20V range and exhibit very
low ESR (in the range of 0.1
).
Figure 6. External Clocking
C2
V
+
100k
OSC INPUT
REQUIRED FOR TTL LOGIC
–(V
+
)
1046 F06
1
2
3
4
8
7
6
5
V
+
OSC
LV
V
OUT
BOOST
CAP
+
GND
CAP
LTC1046
C1
NC
+
+
相關PDF資料
PDF描述
LTC1046IN8 “Inductorless” 5V to + 5V Converter
LTC1046 5V to -5V Monolithic CMOS Switched Voltage Converter(5V 到 -5V單片CMOS開關電容電壓轉換器)
LTC1047C Dual Micropower Chopper Stabilized Operational Amplifier with Internal Capacitors
LTC1047CN8 Dual Micropower Chopper Stabilized Operational Amplifier with Internal Capacitors
LTC1047CS Dual Micropower Chopper Stabilized Operational Amplifier with Internal Capacitors
相關代理商/技術參數
參數描述
LTC1046MJ8 制造商:LINER 制造商全稱:Linear Technology 功能描述:“Inductorless” 5V to + 5V Converter
LTC1047 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Micropower Zero-Drift Operational Amplifier with Internal Capacitors
LTC1047_09 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Micropower Zero-Drift Operational Amplifier with Internal Capacitors
LTC1047C 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual Micropower Chopper Stabilized Operational Amplifier with Internal Capacitors
LTC1047CN8 功能描述:IC OPAMP CHOP-STBL W/CAPS 8-DIP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:J-FET 電路數:2 輸出類型:- 轉換速率:13 V/µs 增益帶寬積:3MHz -3db帶寬:- 電流 - 輸入偏壓:65pA 電壓 - 輸入偏移:3000µV 電流 - 電源:1.4mA 電流 - 輸出 / 通道:- 電壓 - 電源,單路/雙路(±):7 V ~ 36 V,±3.5 V ~ 18 V 工作溫度:-40°C ~ 85°C 安裝類型:通孔 封裝/外殼:8-DIP(0.300",7.62mm) 供應商設備封裝:8-PDIP 包裝:管件