- 您現在的位置：買賣IC網 > PDF目錄377731 > LTC1098AI (Linear Technology Corporation) Micropower Sampling 8-Bit Serial I/O A/D Converters PDF資料下載
參數資料
| 型號： | LTC1098AI |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 串行ADC |
| 英文描述： | Micropower Sampling 8-Bit Serial I/O A/D Converters |
| 中文描述： | 微采樣8位串行I /辦公自動化/ D轉換器 |
| 文件頁數： | 21/28頁 |
| 文件大小： | 452K |
| 代理商： | LTC1098AI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁當前第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
21
LTC1096/LTC1096L
LTC1098/LTC1098L
U
S
A
reference voltage for a typical value of V
OS
. For example,
a V
OS
of 2mV which is 0.1LSB with a 5V reference becomes
0.5LSB with a 1V reference and 2.5LSBs with a 0.2V
reference. If this offset is unacceptable, it can be corrected
digitally by the receiving system or by offsetting the “–”
input of the LTC1096.
O
PPLICATI
IU
U
Noise with Reduced V
REF
The total input referred noise of the LTC1096 can be
reduced to approximately 1mV peak-to-peak using a ground
plane, good bypassing, good layout techniques and mini-
mizing noise on the reference inputs. This noise is insig-
nificant with a 5V reference but will become a larger
fraction of an LSB as the size of the LSB is reduced.
For operation with a 5V reference, the 1mV noise is only
0.05LSB peak-to-peak. In this case, the LTC1096 noise
will contribute virtually no uncertainty to the output
code. However, for reduced references, the noise may
become a significant fraction of an LSB and cause
undesirable jitter in the output code. For example, with a
1V reference, this same 1mV noise is 0.25LSB peak-to-
peak. This will reduce the range of input voltages over
which a stable output code can be achieved by 1LSB. If
the reference is further reduced to 200mV, the 1mV
noise becomes equal to 1.25LSBs and a stable code may
be difficult to achieve. In this case averaging readings
may be necessary.
This noise data was taken in a very clean setup. Any setup-
induced noise (noise or ripple on V
CC
, V
REF
or V
IN
) will add
to the internal noise. The lower the reference voltage to be
used, the more critical it becomes to have a clean, noise free
setup.
Conversion Speed with Reduced V
REF
With reduced reference voltages the LSB step size is
reduced and the LTC1096 internal comparator over-
drive is reduced. Therefore, it may be necessary to
reduce the maximum CLK frequency when low values
of V
REF
are used.
Input Divider
It is OK to use an input divider on the reference input of the
LTC1096 as long as the reference input can be made to
settle within the bit time at which the clock is running.
When using a larger value resistor divider on the reference
input the “–” input should be matched with an equivalent
resistance.
Bypassing Reference Input with Divider
Bypassing the reference input with a divider is also pos-
sible. However, care must be taken to make sure that the
DC voltage on the reference input will not drop too much
below the intended reference voltage.
AC PERFORMANCE
Two commonly used figures of merit for specifying the
dynamic performance of the ADCs in digital signal pro-
cessing applications are the signal-to-noise ratio (SNR)
and the effective number of bits (ENOBs).
Signal-to-Noise Ratio
T
he signal-to-noise ratio (SNR) is the ratio between the
RMS amplitude of the fundamental input frequency to
the RMS amplitude of all other frequency components at
the A/D output. This includes distortion as well as noise
products and for this reason it is sometimes referred to
as signal-to-noise + distortion [S/(N + D)]. The output is
band limited to frequencies from DC to one half the
sampling frequency. Figure 11 shows spectral content
from DC to 15.625kHz which is 1/2 the 31.25kHz sam-
pling rate.
FREQUENCY (kHz)
0
A
–60
–70
–80
–90
–30
–40
–50
–20
16
LTC1096/8 F11
–120
4
8
12
–100
–110
0
–10
2
6
10
14
f
SAMPLE
= 31.25kHz
f
IN
Figure 11. This Clean FFT of an 11.8kHz Input Shows
Remarkable Performance for an ADC That Draws Only 100
μ
A
When Sampling at the 31.25kHz Rate
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1098C | Quad Precision Single Supply Low-Power Operational Amplifier 14-SOIC 0 to 70 |
| LTC1098CS8 | Micropower Sampling 8-Bit Serial I/O A/D Converters |
| LTC1098I | Micropower Sampling 8-Bit Serial I/O A/D Converters |
| LTC1098LC | Micropower Sampling 8-Bit Serial I/O A/D Converters |
| LTC1098CN8 | Micropower Sampling 8-Bit Serial I/O A/D Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1098AIN8 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower Sampling 8-Bit Serial I/O A/D Converters |
| LTC1098AIS8 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower Sampling 8-Bit Serial I/O A/D Converters |
| LTC1098C | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Micropower Sampling 8-Bit Serial I/O A/D Converters |
| LTC1098CN8 | 功能描述:IC A/D CONV 8BIT SRL IN/OUT 8DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC1098CN8#PBF | 功能描述:IC A/D CONV 8BIT SRL IN/OUT 8DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發布緊急采購，3分鐘左右您將得到回復。