- 您現在的位置：買賣IC網 > PDF目錄377735 > LTC1198-1BCS8 (LINEAR TECHNOLOGY CORP) 8-Bit, SO-8, 1MSPS ADCs with Auto-Shutdown Options PDF資料下載
參數資料
| 型號： | LTC1198-1BCS8 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 8-Bit, SO-8, 1MSPS ADCs with Auto-Shutdown Options |
| 中文描述： | 1-CH 8-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| 封裝： | PLASTIC, SOIC-8 |
| 文件頁數： | 18/28頁 |
| 文件大小： | 452K |
| 代理商： | LTC1198-1BCS8 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
18
LTC1196/LTC1198
U
S
A
Clock Frequency
The maximum recommended clock frequency is 14.4MHz
at 25
°
C for the LTC1196/LTC1198 running off a 5V supply.
With the supply voltage changing, the maximum clock
frequency for the devices also changes (see the typical
curve of Maximum Clock Rate vs Supply Voltage). If the
supply is reduced, the clock rate must be reduced also. At
3V the devices are specified with a 5.4MHz clock at 25
°
C.
O
PPLICATI
U
U
Mixed Supplies
It is possible to have a digital system running off a 5V
supply and communicate with the LTC1196/LTC1198
operating on a 3V supply. Achieving this reduces the
outputs of D
OUT
from the ADCs to toggle the equivalent
input of the digital system. The CS, CLK and D
IN
inputs of
the ADCs will take 5V signals from the digital system
without causing any problem (see typical curve of Digital
Input Logic Threshold vs Supply Voltage). With the
LTC1196 operating on a 3V supply, the output of D
OUT
only
goes between 0V and 3V. This signal easily meets TTL
levels (see Figure 6).
Figure 6. Interfacing a 3V Powered LTC1196 to a 5V System
The V
CC
pin should be bypassed to the ground plane with
a 1
μ
F tantalum with leads as short as possible. If the power
supply is clean, the LTC1196/LTC1198 can also operate
with smaller 0.1
μ
F surface mount or ceramic bypass
capacitors. All analog inputs should be referenced directly
to the single-point ground. Digital inputs and outputs
should be shielded from and/or routed away from the
reference and analog circuitry.
SAMPLE-AND-HOLD
Both the LTC1196 and the LTC1198 provide a built-in
sample-and-hold (S&H) function to acquire the input
signal. The S&H acquires the input signal from “+” input
during t
SMPL
as shown in Figures 1 and 2. The S&H of the
LTC1198 can sample input signals in either single-ended
or differential mode (see Figure 7).
Single-Ended Inputs
The sample-and-hold of the LTC1198 allows conversion
of rapidly varying signals. The input voltage is sampled
during the t
SMPL
time as shown in Figure 7. The sampling
interval begins as the bit preceding the first DUMMY bit is
shifted in and continues until the falling CLK edge after the
second DUMMY bit is received. On this falling edge, the
S&H goes into hold mode and the conversion begins.
Differential Inputs
With differential inputs, the ADC no longer converts just a
single voltage but rather the difference between two volt-
ages. In this case, the voltage on the selected “+” input is
still sampled and held and therefore may be rapidly time
varying just as in single-ended mode. However, the volt-
age on the selected “–” input must remain constant and be
free of noise and ripple throughout the conversion time.
Otherwise, the differencing operation may not be per-
formed accurately. The conversion time is 8.5 CLK cycles.
Therefore, a change in the “–” input voltage during this
interval can cause conversion errors. For a sinusoidal
voltage on the “–” input, this error would be:
V
ERROR (MAX)
= V
PEAK
×
2
×
π
×
f(“–”)
×
8.5/f
CLK
Where f(“–”) is the frequency of the “–” input voltage,
V
PEAK
is its peak amplitude and f
CLK
is the frequency of the
BOARD LAYOUT CONSIDERATIONS
Grounding and Bypassing
The LTC1196/LTC1198 are easy to use if some care is
taken. They should be used with an analog ground plane
and single-point grounding techniques. The GND pin
should be tied directly to the ground plane.
3V
4.7
μ
F
MPU
(e.g., 8051)
P1.4
5V
P1.3
P1.2
1196/98 F06
DIFFERENTIAL INPUTS
COMMON-MODE RANGE
0V TO 3V
3V
V
CC
CLK
D
OUT
V
REF
LTC1196
–IN
GND
+IN
CS
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1198-2AC | 8-Bit, SO-8, 1MSPS ADCs with Auto-Shutdown Options |
| LTC1198-2ACS8 | 8-Bit, SO-8, 1MSPS ADCs with Auto-Shutdown Options |
| LTC1198-2BC | 8-Bit, SO-8, 1MSPS ADCs with Auto-Shutdown Options |
| LTC1198-2BCS8 | 8-Bit, SO-8, 1MSPS ADCs with Auto-Shutdown Options |
| LTC1199C | Octal Bus Transceivers/Registers With 3-State Outputs 24-PDIP 0 to 70 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1198-1BCS8#PBF | 功能描述:IC ADC 8BIT 750KHZ SAMPL 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| LTC1198-1BCS8#TR | 功能描述:IC ADC 8BIT 750KHZ SHUTDWN 8SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1198-1BCS8#TRPBF | 功能描述:IC ADC 8BIT 750KHZ SAMPL 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| LTC1198-1BCS8-PBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:8-Bit, SO-8, 1Msps ADCs with Auto-Shutdown Options |
| LTC1198-1BCS8-TRPBF | 制造商:LINER 制造商全稱:Linear Technology 功能描述:8-Bit, SO-8, 1Msps ADCs with Auto-Shutdown Options |
發布緊急采購，3分鐘左右您將得到回復。