- 您現在的位置：買賣IC網 > PDF目錄377736 > LTC1255IS8 (LINEAR TECHNOLOGY CORP) Dual 24V High-Side MOSFET Driver PDF資料下載
參數資料
| 型號： | LTC1255IS8 |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | MOSFETs |
| 英文描述： | Dual 24V High-Side MOSFET Driver |
| 中文描述： | 2 CHANNEL, BUF OR INV BASED MOSFET DRIVER, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 340K |
| 代理商： | LTC1255IS8 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁
5
LTC1255
PI FU
Input Pin
The LTC1255 input pin is active high and activates all of
the protection and charge pump circuitry when switched
ON. The LTC1255 logic and shutdown inputs are high
impedance CMOS gates with ESD protection diodes to
ground and supply and therefore should not be forced
beyond the power supply rails. The input pin should be
held low during the application of power to properly set
the input latch.
U
Gate Drive Pin
The gate drive pin is either driven to ground when the
switch is turned OFF or driven above the supply rail
when the switch is turned ON. This pin is of relatively
high impedance when driven above the rail (the equiva-
lent of a few hundred k
). Care should be taken to
minimize any loading of this pin by parasitic resistance
to ground or supply.
Supply Pin
The supply pin of the LTC1255 serves two vital pur-
poses. The first is obvious; it powers the input, gate
drive, regulation and protection circuitry. The second
purpose is less obvious; it provides a Kelvin connection
to the top of the drain sense resistor for the internal
100mV reference.
The supply pin of the LTC1255 should never be forced
below ground as this may result in permanent damage
to the device A 100
resistor should be inserted in
series with the ground pin if negative supply voltage
transients are anticipated.
The LTC1255 is designed to be continuously powered
so that the gate of the MOSFET is actively driven at all
times. If it is necessary to remove power from the
supply pin and then reapply it, the input pin should be
cycled (low to high) a few milliseconds after the power
is reapplied to reset the input latch and protection
circuitry. Also, the input pin should be isolated from the
controlling logic by a 10k resistor if there is a possibility
that the input pin will be held high after the supply has
been removed.
Drain Sense Pin
The drain sense pin is compared against the supply pin
voltage. If the voltage at this pin is more than 100mV
below the supply pin, the input latch will be reset and
the MOSFET gate will be quickly discharged. Cycle the
input to reset the short-circuit latch and turn the MOSFET
back on.
This pin is also a high impedance CMOS gate with ESD
protection and therefore should not be forced outside
of the power supply rails. To defeat the overcurrent
protection, short the drain sense pin to the supply pin.
Some loads, such as large supply capacitors, lamps or
motors require high in-rush currents. An RC time delay
can be added between the sense resistor and the drain
sense pin to ensure that the drain sense circuitry does
not false trigger during startup. This time constant can
be set from a few microseconds to many seconds.
However, very long delays may put the MOSFET at risk
of being destroyed by a short-circuit condition (see
Applications Information section).
OPERATIOU
The LTC1255 is a dual 24V MOSFET driver with built-in
protection and gate charge pump. The LTC1255 consists
of the following functional blocks:
TTL and CMOS Compatible Inputs and Latches
The LTC1255 inputs have been designed to accommo-
date a wide range of logic families. Both input thresh-
olds are set at about 1.3V with approximately 100mV of
hysteresis. A low standby current regulator provides
continuous bias for the TTL-to-CMOS converter.
The input/protection latch should be set after initial
power-up, or after reapplication of power, by cycling
the input low to high.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1258-2.5 | Micropower Low Dropout References(2.5V輸出,微功耗，低壓差電壓基準) |
| LTC1258-4.1 | Micropower Low Dropout References(4.1V輸出,微功耗，低壓差電壓基準) |
| LTC1258-5 | Micropower Low Dropout References(5V輸出,微功耗，低壓差電壓基準) |
| LTC1258-3 | Micropower Low Dropout References(3V輸出,微功耗，低壓差電壓基準) |
| LTC1261CS | Switched Capacitor Regulated Voltage Inverter |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1255IS8#PBF | 功能描述:IC MOSFET DVR HI-SIDE DUAL 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:5 系列:- 配置:低端 輸入類型:非反相 延遲時間:600ns 電流 - 峰:12A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:14.2 V ~ 15.8 V 工作溫度:-20°C ~ 60°C 安裝類型:通孔 封裝/外殼:21-SIP 模塊 供應商設備封裝:模塊 包裝:散裝 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名稱:835-1063 |
| LTC1255IS8#TR | 功能描述:IC DRVR MOSF DUAL 24V HISD 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:5 系列:- 配置:低端 輸入類型:非反相 延遲時間:600ns 電流 - 峰:12A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:14.2 V ~ 15.8 V 工作溫度:-20°C ~ 60°C 安裝類型:通孔 封裝/外殼:21-SIP 模塊 供應商設備封裝:模塊 包裝:散裝 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名稱:835-1063 |
| LTC1255IS8#TRPBF | 功能描述:IC MOSFET DVR HI-SIDE DUAL 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - MOSFET，電橋驅動器 - 外部開關 系列:- 標準包裝:5 系列:- 配置:低端 輸入類型:非反相 延遲時間:600ns 電流 - 峰:12A 配置數:1 輸出數:1 高端電壓 - 最大（自引導啟動）:- 電源電壓:14.2 V ~ 15.8 V 工作溫度:-20°C ~ 60°C 安裝類型:通孔 封裝/外殼:21-SIP 模塊 供應商設備封裝:模塊 包裝:散裝 配用:BG2A-NF-ND - KIT DEV BOARD FOR IGBT 其它名稱:835-1063 |
| LTC1257CN8 | 功能描述:IC D/A CONV 12BIT VOLT OUT 8-DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:LTC263x 12-, 10-, and 8-Bit VOUT DAC Family 特色產品:LTC2636 - Octal 12-/10-/8-Bit SPI VOUT DACs with 10ppm/°C Reference 標準包裝:91 系列:- 設置時間:4µs 位數:10 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:8 電壓電源:單電源 功率耗散（最大）:2.7mW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-WFDFN 裸露焊盤 供應商設備封裝:14-DFN-EP（4x3） 包裝:管件 輸出數目和類型:8 電壓，單極 采樣率（每秒）:* |
| LTC1257CN8#PBF | 功能描述:IC D/A CONV 12BIT VOLT OUT 8-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。