- 您現在的位置：買賣IC網 > PDF目錄10228 > LTC1403AHMSE#PBF (Linear Technology)IC ADC 14BIT 2.8MSPS DIFF 10MSOP PDF資料下載
參數資料
| 型號： | LTC1403AHMSE#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 14BIT 2.8MSPS DIFF 10MSOP |
| 標準包裝： | 50 |
| 位數： | 14 |
| 采樣率（每秒）： | 2.8M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 12mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 |
| 供應商設備封裝： | 10-MSOP 裸露焊盤 |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，單極；1 個差分，單極 |
| 配用： | DC1082A-D-ND - BOARD SAR ADC LTC1403A DC1082A-C-ND - BOARD SAR ADC LTC1403A-1 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁
LTC1403/LTC1403A
13
1403fb
APPLICATIONS INFORMATION
intervening rising edges at SCK, put the LTC1403/LTC1403A
in Sleep mode and the power drain drops from 16mW
to 10μW. One or more rising edges at SCK wake up the
LTC1403/LTC1403A for operation. The internal reference
(VREF) takes 2ms to slew and settle with a 10μF load.
Note that, using sleep mode more frequently than every
2ms, compromises the settled accuracy of the internal
reference. Note that, for slower conversion rates, the Nap
and Sleep modes can be used for substantial reductions
in power consumption.
DIGITAL INTERFACE
The LTC1403/LTC1403A has a 3-wire SPI (Serial Protocol
Interface) interface. The SCK and CONV inputs and SDO
output implement this interface. The SCK and CONV inputs
accept swings from 3V logic and are TTL compatible, if the
logic swing does not exceed VDD. A detailed description
of the three serial port signals follows:
Conversion Start Input (CONV)
The rising edge of CONV starts a conversion, but subse-
quent rising edges at CONV are ignored by the LTC1403/
LTC1403A until the following 16 SCK rising edges have
occurred. It is necessary to have a minimum of 16 rising
edges of the clock input SCK between rising edges of CONV.
But to obtain maximum conversion speed, it is necessary
to allow two more clock periods between conversions to
allow 39ns of acquisition time for the internal ADC sample-
and-hold circuit. With 16 clock periods per conversion,
the maximum conversion rate is limited to 2.8Msps to
allow 39ns for acquisition time. In either case, the output
data stream comes out within the rst 16 clock periods to
ensure compatibility with processor serial ports. The duty
cycle of CONV can be arbitrarily chosen to be used as a
frame sync signal for the processor serial port. A simple
approach to generate CONV is to create a pulse that is
one SCK wide to drive the LTC1403/LTC1403A and then
buffer this signal with the appropriate number of inverters
to ensure the correct delay driving the frame sync input of
the processor serial port. It is good practice to drive the
LTC1403/LTC1403A CONV input rst to avoid digital noise
interference during the sample-to-hold transition triggered
by CONV at the start of conversion. It is also good practice
to keep the width of the low portion of the CONV signal
greater than 15ns to avoid introducing glitches in the front
end of the ADC just before the sample-and-hold goes into
hold mode at the rising edge of CONV.
Minimizing Jitter on the CONV Input
In high speed applications where high amplitude sinewaves
above 100kHz are sampled, the CONV signal must have
as little jitter as possible (10ps or less). The square wave
output of a common crystal clock module usually meets
this requirement easily. The challenge is to generate a CONV
signal from this crystal clock without jitter corruption from
other digital circuits in the system. A clock divider and
any gates in the signal path from the crystal clock to the
CONV input should not share the same integrated circuit
with other parts of the system. As shown in the interface
circuit examples, the SCK and CONV inputs should be
driven rst, with digital buffers used to drive the serial port
interface. Also note that the master clock in the DSP may
already be corrupted with jitter, even if it comes directly
from the DSP crystal. Another problem with high speed
processor clocks is that they often use a low cost, low
speed crystal (i.e., 10MHz) to generate a fast, but jittery,
phase-locked-loop system clock (i.e., 40MHz). The jitter
in these PLL-generated high speed clocks can be several
nanoseconds. Note that if you choose to use the frame
sync signal generated by the DSP port, this signal will
have the same jitter of the DSP’s master clock.
Serial Clock Input (SCK)
The rising edge of SCK advances the conversion process
and also udpates each bit in the SDO data stream. After
CONV rises, the third rising edge of SCK starts clocking out
the 12/14 data bits with the MSB sent rst. A simple ap-
proach is to generate SCK to drive the LTC1403/LTC1403A
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1855CG#PBF | IC ADC 14BIT 8CH 100KSPS 28SSOP |
| SP1485ECN-L/TR | IC TXRX RS485 DIFF ESD 8SOIC |
| SP3232EUEA-L/TR | IC TXRX RS232 ESD 16SSOP |
| AD7575JNZ | IC ADC 8BIT LC2MOS W/HOLD 18DIP |
| SP3232EBEA-L/TR | IC TXRX RS232 ESD TRUE 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1403AIMSE | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1403AIMSE#PBF | 功能描述:IC ADC 14BIT 2.8MSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC1403AIMSE#TR | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1403AIMSE#TRPBF | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1403AIMSE-1 | 功能描述:IC ADC 14BIT 2.8MSPS DIFF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。