- 您現在的位置：買賣IC網 > PDF目錄10319 > LTC1403CMSE-1#TRPBF (Linear Technology)IC ADC 12BIT 2.8MSPS DIFF 10MSOP PDF資料下載
參數資料
| 型號： | LTC1403CMSE-1#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 7/22頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 2.8MSPS DIFF 10MSOP |
| 標準包裝： | 2,500 |
| 位數： | 12 |
| 采樣率（每秒）： | 2.8M |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 12mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬）裸露焊盤 |
| 供應商設備封裝： | 10-MSOP 裸露焊盤 |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個單端，單極；1 個差分，單極 |
| 配用： | DC1082A-D-ND - BOARD SAR ADC LTC1403A DC1082A-C-ND - BOARD SAR ADC LTC1403A-1 |
LTC1403-1/LTC1403A-1
15
14031fc
APPLICATIONS INFORMATION
One or more rising edges at SCK wake up the LTC1403-1/
LTC1403A-1 for service very quickly, and CONV can start
an accurate conversion within a clock cycle. Four rising
edges at CONV, without any intervening rising edges at
SCK, put the LTC1403-1/LTC1403A-1 in Sleep mode and
the power drain drops from 16mW to 10W. One or more
rising edges at SCK wake up the LTC1403-1/LTC1403A-1
for operation. The internal reference (VREF ) takes 2ms to
slew and settle with a 10F load. Note that, using sleep
mode more frequently than every 2ms, compromises the
settled accuracy of the internal reference. Note that, for
slower conversion rates, the Nap and Sleep modes can be
used for substantial reductions in power consumption.
DIGITAL INTERFACE
The LTC1403-1/LTC1403A-1 has a 3-wire SPI (Serial Pro-
tocol Interface) interface. The SCK and CONV inputs and
SDO output implement this interface. The SCK and CONV
inputs accept swings from 3V logic and are TTL compat-
ible, if the logic swing does not exceed VDD. A detailed
description of the three serial port signals follows:
Conversion Start Input (CONV)
The rising edge of CONV starts a conversion, but
subsequent rising edges at CONV are ignored by the
LTC1403-1/LTC1403A-1 until the following 16 SCK rising
edges have occurred. It is necessary to have a minimum
of 16 rising edges of the clock input SCK between ris-
ing edges of CONV. But to obtain maximum conversion
speed, it is necessary to allow two more clock periods
between conversions to allow 39ns of acquisition time
for the internal ADC sample-and-hold circuit. With 16
clock periods per conversion, the maximum conversion
rate is limited to 2.8Msps to allow 39ns for acquisition
time. In either case, the output data stream comes out
within the first 16 clock periods to ensure compatibility
with processor serial ports. The duty cycle of CONV can
be arbitrarily chosen to be used as a frame sync signal for
the processor serial port. A simple approach to generate
CONV is to create a pulse that is one SCK wide to drive the
LTC1403-1/LTC1403A-1 and then buffer this signal with
the appropriate number of inverters to ensure the correct
delay driving the frame sync input of the processor serial
port.ItisgoodpracticetodrivetheLTC1403-1/LTC1403A-1
CONV input first to avoid digital noise interference during
the sample-to-hold transition triggered by CONV at the
start of conversion. It is also good practice to keep the
width of the low portion of the CONV signal greater than
15ns to avoid introducing glitches in the front end of the
ADC just before the sample-and-hold goes into hold mode
at the rising edge of CONV.
Minimizing Jitter on the CONV Input
Inhighspeedapplicationswherehighamplitudesinewaves
above 100kHz are sampled, the CONV signal must have
as little jitter as possible (10ps or less). The square wave
output of a common crystal clock module usually meets
thisrequirementeasily.ThechallengeistogenerateaCONV
signalfromthiscrystalclockwithoutjittercorruptionfrom
other digital circuits in the system. A clock divider and
any gates in the signal path from the crystal clock to the
CONV input should not share the same integrated circuit
with other parts of the system. As shown in the interface
circuit examples, the SCK and CONV inputs should be
driven first, with digital buffers used to drive the serial port
interface. Also note that the master clock in the DSP may
already be corrupted with jitter, even if it comes directly
from the DSP crystal. Another problem with high speed
processor clocks is that they often use a low cost, low
speed crystal (i.e., 10MHz) to generate a fast, but jittery,
phase-locked-loop system clock (i.e., 40MHz). The jitter
in these PLL-generated high speed clocks can be several
nanoseconds. Note that if you choose to use the frame
sync signal generated by the DSP port, this signal will
have the same jitter of the DSP’s master clock.
Serial Clock Input (SCK)
The rising edge of SCK advances the conversion process
and also udpates each bit in the SDO data stream. After
CONV rises, the third rising edge of SCK starts clocking
out the 12/14 data bits with the MSB sent first. A simple
approach is to generate SCK to drive the LTC1403-1/
LTC1403A-1 first and then buffer this signal with the
appropriate number of inverters to drive the serial clock
input of the processor serial port. Use the falling edge of
相關PDF資料 |
PDF描述 |
|---|---|
| MS27468E13B35SA | CONN RCPT 22POS JAM NUT W/SCKT |
| D38999/20MH21BN | CONN HSG RCPT 21POS WALL MT SCKT |
| AD7401YRWZ-REEL | IC MODULATOR SIGMA-DELTA 16SOIC |
| MS3108A14S-5P | CONN PLUG 5POS RT ANG W/PINS |
| LTC1407CMSE | IC ADC 12BIT 3MSPS SAMPLE 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1403HMSE#PBF | 功能描述:IC ADC 12BIT 2.8MSPS DIFF 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1403HMSE#TRPBF | 功能描述:IC ADC 12BIT 2.8MSPS DIFF 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1403IMSE | 功能描述:IC ADC 12BIT 2.8MSPS DIFF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1403IMSE#PBF | 功能描述:IC ADC 12BIT 2.8MSPS 10-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC1403IMSE#TR | 功能描述:IC ADC 12BIT 2.8MSPS DIFF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。