- 您現在的位置：買賣IC網 > PDF目錄10228 > LTC1410ISW (Linear Technology)IC A/D CONV 12BIT SAMPLNG 28SOIC PDF資料下載
參數資料
| 型號： | LTC1410ISW |
| 廠商： | Linear Technology |
| 文件頁數： | 4/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC A/D CONV 12BIT SAMPLNG 28SOIC |
| 標準包裝： | 27 |
| 位數： | 12 |
| 采樣率（每秒）： | 1.25M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 230mW |
| 電壓電源： | 雙 ± |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 28-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 28-SOIC |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，雙極；1 個差分，雙極 |
| 其它名稱： | LTC1410IS |
12
LTC1410
APPLICATIONS INFORMATION
WU
U
High quality tantalum and ceramic bypass capacitors
should be used at the VDD, VSS and REFCOMP pins as
shown in the Typical Application on the first page of this
data sheet. Bypass capacitors must be located as close to
the pins as possible. The traces connecting the pins and
bypass capacitors must be kept short and should be made
as wide as possible.
The LTC1410 has differential inputs to minimize noise
coupling. Common mode noise on the + AIN and – AIN
leads will be rejected by the input CMRR. The – AIN input
can be used as a ground sense for the + AIN input; the
LTC1410 will hold and convert the difference voltage
between + AIN and –AIN. The leads to + AIN (Pin 1) and – AIN
(Pin 2) should be kept as short as possible. In applications
where this is not possible, the + AIN and – AIN traces should
be run side by side to equalize coupling.
A single point analog ground separate from the logic
system ground should be established with an analog
ground plane at Pin 5 (AGND) or as close as possible to the
ADC. Pin 14 and Pin 19 (ADC’s DGND) and all other analog
grounds should be connected to this single analog ground
point. No other digital grounds should be connected to this
analog ground point. Low impedance analog and digital
power supply common returns are essential to low noise
operation of the ADC and the foil width for these tracks
should be as wide as possible. In applications where the
ADC data outputs and control signals are connected to a
continuously active microprocessor bus, it is possible to
get errors in the conversion results. These errors are due
to feedthrough from the microprocessor to the successive
approximation comparator. The problem can be elimi-
nated by forcing the microprocessor into a wait state
during conversion or by using three-state buffers to iso-
late the ADC data bus.
DIGITAL INTERFACE
The A/D converter is designed to interface with micropro-
cessors as a memory mapped device. The CS and RD
control inputs are common to all peripheral memory
interfacing. A separate CONVST is used to initiate a con-
version.
Internal Clock
The A/D converter has an internal clock that eliminates the
need of synchronization between the external clock and
the CS and RD signals found in other ADCs. The internal
clock is factory trimmed to achieve a typical conversion
time of 0.65
s and a maximum conversion time over the
full operating temperature range of 0.75
s. No external
adjustments are required. The guaranteed maximum ac-
quisition time is 100ns. In addition, throughput time of
800ns and a minimum sampling rate of 1.25Msps is
guaranteed.
1410 F11
DIGITAL
SYSTEM
0.1
F
ANALOG
INPUT
CIRCUITRY
4
2
26
19
14
1
0.1
F
10
F
10
F
+
–
0.1
F
28
27
10
F
+AIN
–AIN
AGND
REFCOMP
AVDD
VSS
DVDD DGND OGND
LTC1410
Figure 11. Power Supply Grounding Practice
相關PDF資料 |
PDF描述 |
|---|---|
| VE-2N2-IW-S | CONVERTER MOD DC/DC 15V 100W |
| VE-2N2-CU-F4 | CONVERTER MOD DC/DC 15V 200W |
| VE-2N2-CU-F3 | CONVERTER MOD DC/DC 15V 200W |
| VE-2N2-CU-F2 | CONVERTER MOD DC/DC 15V 200W |
| VI-211-IU-F3 | CONVERTER MOD DC/DC 12V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1410ISW#PBF | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1410ISW#TR | 功能描述:IC ADC 12BIT 1.25MSPS SMP 28SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1410ISW#TRPBF | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC1411CG | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1411CG#PBF | 功能描述:IC ADC 14BIT 2.5MSPS 36SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。