- 您現在的位置：買賣IC網 > PDF目錄10146 > LTC1411CG#TRPBF (Linear Technology)IC A/D CONV 14BIT 2.5MSPS 36SSOP PDF資料下載
參數資料
| 型號： | LTC1411CG#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 2/16頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC A/D CONV 14BIT 2.5MSPS 36SSOP |
| 標準包裝： | 1,000 |
| 位數： | 14 |
| 采樣率（每秒）： | 2.5M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 325mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 36-SSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個單端，雙極；1 個差分，雙極 |
10
LTC1411
1411f
the sampling capacitor, choose an amplifier that has a low
output impedance (<100
) at the closed-loop bandwidth
frequency. For example, if an amplifier is used in a gain of
1 and has a unity-gain bandwidth of 50MHz, then the
output impedance at 50MHz must be less than 100
. The
second requirement is that the closed-loop bandwidth
must be greater than 40MHz to ensure adequate small-
signal settling for full throughput rate. If slower op amps
are used, more settling time can be provided by increasing
the time between conversions.
The best choice for an op amp to drive the LTC1411 will
depend on the application. Generally applications fall into
two categories: AC applications where dynamic specifica-
tions are most critical and time domain applications where
DC accuracy and settling time are most critical. The
following list is a summary of the op amps that are suitable
for driving the LTC1411. More detailed information is
available in the Linear Technology Databooks and on the
LinearView
TM CD-ROM.
LT
1227: 140MHz Video Current Feedback Amplifier.
10mA supply current.
±5V to ±15V supplies. Low noise.
Good for AC applications.
LT1395: 400MHz Current Feedback Amplifier. Single 5V
or
±5V supplies. Good for AC applications.
LT1800: 80MHz, 25V/
sLowPowerRail-to-RailInputand
Output Precision Op Amp. Specified at 3V, 5V and
±5V
supplies. Excellent DC performance.
Peak Harmonic or Spurious Noise
The peak harmonic or spurious noise is the largest spec-
tral component excluding the input signal and DC. This
value is expressed in dB relative to the RMS value of a full-
scale input signal.
Full-Power and Full-Linear Bandwidth
The full-power bandwidth is that input frequency at which
the amplitude of the reconstructed fundamental is re-
duced by 3db for a full-scale input signal.
The full-linear bandwidth is the input frequency at which
the S/(N + D) has dropped to 74dB (12 effective bits). The
LTC1411 has been designed to optimize input bandwidth,
allowing the ADC to undersample input signals with fre-
quencies above the converter’s Nyquist frequency. The
noise floor stays very low at high frequencies; S/(N + D)
becomes dominated by distortion at frequencies far be-
yond Nyquist.
Driving the Analog Input
The differential analog inputs of the LTC1411 are easy to
drive. The inputs may be driven differentially or as a single-
ended input (i.e., the AIN– input is tied to a fixed DC voltage
such as the REFOUT pin of the LTC1411 or an external
source). Figure 1 shows a simplified block diagram for the
analog inputs of the LTC1411. The AIN+ and AIN– are
sampled at the same instant. Any unwanted signal that is
common mode to both inputs will be reduced by the
common mode rejection of the sample-and-hold circuit.
The inputs draw only one small current spike while charg-
ing the sample-and-hold capacitors at the end of conver-
sion. During conversion, the analog inputs draw only a
small leakage current. If the source impedance of the
driving circuits is low, then the LTC1411 inputs can be
driven directly. More acquisition time should be allowed
for a higher impedance source. Figure 5 shows the acqui-
sition time versus source resistance.
Choosing an Input Amplifier
Choosing an input amplifier is easy if a few requirements
are taken into consideration. First, to limit the magnitude
of the voltage spike seen by the amplifier from charging
APPLICATIO S I FOR ATIO
WU
UU
SOURCE RESISTANCE (
)
1
ACQUISITION
TIME
(
s)
1
10
10000
1411 G16
0.1
0.01
10
100
1000
100000
100
Figure 5. Acquisition Time vs Source Resistance
LinearView is a trademark of Linear Technology Corporation.
相關PDF資料 |
PDF描述 |
|---|---|
| SP3245EEA-L | IC TXRX RS232 28SSOP |
| MS3101R14S-2S | CONN RCPT 4POS PANEL MNT W/SCKT |
| IDT7201LA25SO8 | IC MEM FIFO 512X9 25NS 28-SOIC |
| LTC2856HMS8-2#PBF | IC TXRX RS485/RS422 8-MSOP |
| MS3102R18-1SZ | CONN RCPT 10POS BOX MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1411IG | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1411IG#PBF | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| LTC1411IG#TR | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1411IG#TRPBF | 功能描述:IC A/D CONV 14BIT 2.5MSPS 36SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
| LTC1412CG | 功能描述:IC A/D CONV 12BIT SAMPLNG 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。