- 您現在的位置：買賣IC網 > Datasheet目錄41 > LTC1421ISW-2.5#PBF (Linear Technology)IC CONTROLLER HOT SWAP 24-SOIC Datasheet資料下載
參數資料
| 型號： | LTC1421ISW-2.5#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 329K |
| 描述： | IC CONTROLLER HOT SWAP 24-SOIC |
| 標準包裝： | 32 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 3 V ~ 12 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SOIC（0.295"，7.50mm 寬） |
| 供應商設備封裝： | 24-SOIC |
| 包裝： | 管件 |
11
LTC1421/LTC1421-2.5
APPLICATIONS INFORMATION
U
U
U
is connected between REF (Pin 8) and the negative supply
and the trip point of Comparator 2 set to GND.
Soft Reset Generation
A soft reset that doesnt cycle the supply voltage can be
generated externally using Pin 11 (FB) as shown in Figure
9. For a 5V supply the FB pin is left floating to set the
internal supply monitor trip voltage to 4.65V. However, if
the FB pin is pulled to ground for more than 32祍 via a push
button or open-collector logic gate, the internal trip point
will go to 5.88V and the RESET pin will pull low. RESET will
remain low for 200ms after the FB pin is released. The
RESET signal will also be pulled low when the voltage at
the V
OUTLO
pin dips below 4.65V for more than 32祍.
When using a 3.3V supply, a 1k resistor must be con-
nected from the FB pin to V
CCLO
to set the internal trip point
to 2.90V.
sense resistor is greater than 50mV for more than 20祍.
When the circuit breaker trips, both N-channel MOSFETs
are quickly turned off, FAULT and PWRGD go low and
RESET is pulled low 32祍 later. FAULT can be connected
to a LED or a logic signal back to the host to indicate a faulty
board. The chip will remain in the tripped state until a
power-on reset is generated, or the power on V
CCHI
and
V
CCLO
is cycled. If the circuit breaker feature is not used,
short V
CCLO
to SETLO and V
CCHI
to SETHI.
If more than 20祍 of response time is needed to reject
supply noise, an external resistor and capacitor can be
added to the sense circuit as shown in Figure 10.
Figure 9. Generating a Soft Reset
Undervoltage Lockout
On power-up, an undervoltage lockout circuit prevents the
GATELO and GATEHI charge pumps from turning on until
V
CCLO
and V
CCHI
have both exceeded 2.45V.
Electronic Circuit Breaker
The LTC1421 features an electronic circuit breaker func-
tion that protects against short circuits or excessive cur-
rents on the supplies. By placing a sense resistor between
the supply input and set pin of either supply, the circuit
breaker will be tripped whenever the voltage across the
LTC1421
3.3V
5V
1/6 LS7404
OPEN
COLLECTOR
GND
32祍
200ms
FB
11
7
12
1421 F09
R1
1k
R1 USED FOR 3.3V
SUPPLY ONLY
RESET
RESET
FB
RESET
LOGIC
23
R
SENSE
C
F
Q1
22
R
F
21
20
V
CCLO
SETLO GATELO V
OUTLO
LTC1421
1421 F10
4
3
2
1
Figure 10. Short-Circuit Protection Circuit
Figure 11. AUXV
CC
Circuitry
GATE DRIVE
CIRCUITRY
10k
1礔
AUXV
CC
1421 F11
V
CCLO
24
LTC1421
23
GATELO GATEHI
21
17
Auxiliary V
CC
When a short circuit occurs on the board, it is possible to
draw enough current to cause the backplane supply
voltage to collapse. If the input supply voltage collapses to
a low enough voltage and the LTC1421 gate drive circuitry
is unable to shut off the N-channel pass transistors, the
system might freeze up in a permanent short condition.
To prevent this from occurring, the gate discharge cir-
cuitry inside the LTC1421 is powered from AUXV
CC
,
which is in turn powered from V
CCLO
through an internal
Schottky diode and current limiting resistor (Figure 11).
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1422CN8 | IC CONTROLLER HOT SWAP 8-DIP |
| LTC1642CGN#TRPBF | IC CONTROLLER HOTSWAP ADJ 16SSOP |
| LTC1643AL-1CGN#PBF | IC CTRLR HOTSWAP PCI BUS 16SSOP |
| LTC1644CGN#TRPBF | IC CONTROLLER HOT SWAP 20-SSOP |
| LTC1645IS#TRPBF | IC CTRLR SEQ HOTSWAP DUAL 14SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1422CN8 | 功能描述:IC CONTROLLER HOT SWAP 8-DIP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC1422CN8#PBF | 功能描述:IC CONTROLLER HOT SWAP 8-DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC1422CS8 | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC1422CS8#PBF | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC1422CS8#TR | 功能描述:IC CONTROLLER HOTSWAP 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。