- 您現在的位置：買賣IC網 > Datasheet目錄41 > LTC1422CN8 (Linear Technology)IC CONTROLLER HOT SWAP 8-DIP Datasheet資料下載
參數資料
| 型號： | LTC1422CN8 |
| 廠商： | Linear Technology |
| 文件頁數： | 5/16頁 |
| 文件大?。?/td> | 197K |
| 描述： | IC CONTROLLER HOT SWAP 8-DIP |
| 標準包裝： | 50 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 2.7 V ~ 12 V |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 通孔 |
| 封裝/外殼： | 8-DIP（0.300"，7.62mm） |
| 供應商設備封裝： | 8-PDIP |
| 包裝： | 管件 |
| 產品目錄頁面： | 1341 (CN2011-ZH PDF) |
5
LTC1422
1422fb
TYPICAL PERFORMANCE CHARACTERISTICS
W
PIN FUNCTIONS
U
U
TIMER (Pin 3): Analog system timing generator pin. This
pin is used to set the delay before the charge pump turns
on after the ON pin goes high. It also sets the delay before
the RESET pin goes high, after the output supply voltage
is good, as sensed by the FB pin.
When the timer is off, an internal N-channel shorts the
TIMER pin to ground. When the timer is turned on, a 2礎
current from V
CC
is connected to the TIMER pin and the
voltage starts to ramp up with a slope given by: dV/dt =
2礎/C
TIMER
. When the voltage reaches the trip point
(1.232V), the timer will be reset by pulling the TIMER pin
back to ground. The timer period is given by: (1.232V "
C
TIMER
)/2礎.
GND (Pin 4): Chip Ground.
FB (Pin 5): Analog comparator input used to monitor the
output supply voltage with an external resistive divider.
When the voltage on the FB pin is lower than the 1.232V,
the RESET pin will be pulled low. An internal filter helps
prevent negative voltage glitches from triggering a reset.
When the voltage on the FB pin rises above the trip point,
the RESET pin will go high after one timing cycle.
RESET (Pin 1) : Open drain output to GND with a 12?/SPAN>A
pull-up to V
CC
. This pin is pulled low when the voltage at
the FB (Pin 5) goes below the FB pin threshold. The RESET
pin will go high one timing cycle after the voltage at the FB
pin goes above the FB pin threshold. An external pull-up
resistor can be used to speed up the rising edge on the
RESET pin or pull the pin to a voltage higher or lower than
V
CC
.
ON (Pin 2): Analog Input Pin. The threshold is set at 1.30V
with 80mV hysteresis. When the ON pin is pulled high, the
timer turns on for one cycle, then the charge pump turns
on. When the ON pin is pulled low longer than 40祍, the
GATE pin will be pulled low and remain off until the ON pin
is pulled high.
If the ON pin is pulled low for less than 15祍 a soft reset
will occur. The charge pump remains on, and the RESET
pin is pulled low for one timing cycle starting 30祍 from
the falling edge of the ON pin.
The ON pin is also used to reset the electronic circuit
breaker. If the ON pin is cycled low and high following the
trip of the circuit breaker, the circuit breaker is reset and
a normal power-up sequence will occur.
RESET Voltage vs Temperature
TEMPERATURE (癈)
55
65
0.24
0.22
0.20
0.18
0.16
0.14
0.12
0.10
0.08
0.06
1422 G19
5
35
85
25
15
105
45
125
V
CC
= 5V
3mA PULL-UP
TEMPERATURE (癈)
55
65
55
50
45
40
35
30
25
20
15
10
1422 G20
5
35
85
25
15
105
45
125
V
CC
= 12V
V
CC
= 5V
V
CC
= 3V
ON Pin Pulse (Soft Reset) Time
vs Temperature
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1642CGN#TRPBF | IC CONTROLLER HOTSWAP ADJ 16SSOP |
| LTC1643AL-1CGN#PBF | IC CTRLR HOTSWAP PCI BUS 16SSOP |
| LTC1644CGN#TRPBF | IC CONTROLLER HOT SWAP 20-SSOP |
| LTC1645IS#TRPBF | IC CTRLR SEQ HOTSWAP DUAL 14SOIC |
| LTC1646IGN#TR | IC CNTRLR HOTSWAP PCIDUAL 16SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1422CN8#PBF | 功能描述:IC CONTROLLER HOT SWAP 8-DIP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC1422CS8 | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC1422CS8#PBF | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC1422CS8#TR | 功能描述:IC CONTROLLER HOTSWAP 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC1422CS8#TRPBF | 功能描述:IC CONTROLLER HOT SWAP 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。