- 您現在的位置：買賣IC網 > PDF目錄377747 > LTC1435AC (Linear Technology Corporation) 14-bit, 5V, 200KSPS, 8-Channel Unipolar ADC 24-TSSOP -40 to 85 PDF資料下載
參數資料
| 型號： | LTC1435AC |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 14-bit, 5V, 200KSPS, 8-Channel Unipolar ADC 24-TSSOP -40 to 85 |
| 中文描述： | 高效率低噪聲同步降壓型開關穩壓器 |
| 文件頁數： | 12/20頁 |
| 文件大?。?/td> | 427K |
| 代理商： | LTC1435AC |
12
LTC1435A
APPLICATIO
S I
FOR
ATIO
U
The external resistive divider is connected to the output as
shown in Figure 5 allowing remote voltage sensing.
W
U
U
V
OSENSE
LTC1435A
R1
R2
1435A F05
100pF
1.19V
≤
V
OUT
≤
9V
SGND
Figure 5. Setting the LTC1435A Output Voltage
Run/Soft Start Function
The RUN/SS pin is a dual purpose pin that provides the soft
start function and a means to shut down the LTC1435A. Soft
start reduces surge currents from V
IN
by gradually increas-
ing the internal current limit. Power supply sequencingcan
also be accomplished using this pin.
An internal 3
μ
A current source charges up an external
capacitor C
SS.
When the voltage on RUN/SS reaches 1.3V
the LTC1435A begins operating. As the voltage on RUN/SS
continues to ramp from 1.3V to 2.4V, the internal current
limit is also ramped at a proportional linear rate. The cur-
rent limit begins at approximately 50mV/R
SENSE
(at V
RUN/
SS
= 1.3V) and ends at 150mV/R
SENSE
(V
RUN/SS
> 2.7V). The
output current thus ramps up slowly, charging the output
capacitor. If RUN/SS has been pulled all the way to ground
there is a delay before starting of approximately 500ms/
μ
F,
followed by an additional 500ms/
μ
F to reach full current.
t
DELAY
= 5(10
5
)C
SS
Seconds
Pulling the RUN/SS pin below 1.3V puts the LTC1435A into
a low quiescent current shutdown (I
Q
< 25
μ
A). This pin can
be driven directly from logic as shown in Figure 6. Diode
D1 in Figure 6 reduces the start delay but allows C
SS
to ramp
up slowly for the soft start function; this diode and C
SS
can
be deleted if soft start is not needed. The RUN/SS pin has
an internal 6V Zener clamp (See Functional Diagram).
Foldback Current Limiting
As described in Power MOSFET and D1 Selection, the worst-
case dissipation for either MOSFET occurs with a short-
circuited output, when the synchronous MOSFET conducts
the current limit value almost continuously. In most appli-
cations this will not cause excessive heating, even for
extended fault intervals. However, when heat sinking is at
a premium or higher R
DS(ON)
MOSFETs are being used,
foldback current limiting should be added to reduce the
current in proportion to the severity of the fault.
Foldback current limiting is implemented by adding diode
D
FB
between the output and the I
TH
pin as shown in the
Functional Diagram. In a hard short (V
OUT
= 0V) the cur-
rent will be reduced to approximately 25% of the maximum
output current. This technique may be used for all applica-
tions with regulated output voltages of 1.8V or greater.
SFB Pin Operation
When the SFB pin drops below its ground referenced 1.19V
threshold, continuous mode operation is forced. In continu-
ous mode, the large N-channel main and synchronous
switches are used regardless of the load on the main output.
In addition to providing a logic input to force continuous
synchronous operation, the SFB pin provides a means to
regulate a flyback winding output. Continuous synchronous
operation allows power to be drawn from the auxiliary
windings without regard to the primary output load. The SFB
pin provides a way to force continuous synchronous op-
eration as needed by the flyback winding.
The secondary output voltage is set by the turns ratio of the
transformer in conjunction with a pair of external resistors
returned to the SFB pin as shown in Figure 4a. The second-
ary regulated voltage, V
SEC
, in Figure 4a is given by:
V
N
V
R
R
SEC
OUT
≈
+
(
)
>
+
1
1 19 1
.
6
5
where N is the turns ratio of the transformer and V
OUT
is
the main output voltage sensed by V
OSENSE
.
Minimum On-Time Considerations
Minimum on-time, t
ON(MIN)
, is the smallest amount of time
that the LTC1435A is capable of turning the top MOSFET
1435 F06
C
SS
D1
3.3V OR 5V
RUN/SS
C
SS
RUN/SS
Figure 6. RUN/SS Pin Interfacing
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1435ACG | 14-bit, 5V, 200KSPS, 8-Channel Unipolar ADC 24-TSSOP -40 to 85 |
| LTC1435ACS | 14-bit, 5V, 200KSPS, 8-Channel Unipolar ADC 24-TSSOP -40 to 85 |
| LTC1435AI | High Efficiency Low Noise Synchronous Step-Down Switching Regulator |
| LTC1435AIG | High Efficiency Low Noise Synchronous Step-Down Switching Regulator |
| LTC1435AIS | High Efficiency Low Noise Synchronous Step-Down Switching Regulator |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1435ACG | 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1435ACG#PBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,000 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:1MHz 占空比:50% 電源電壓:9 V ~ 10 V 降壓:無 升壓:是 回掃:是 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP（0.173"，4.40mm 寬） 包裝:帶卷 (TR) |
| LTC1435ACG#TR | 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1435ACG#TRPBF | 功能描述:IC REG CTRLR BUCK PWM CM 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
| LTC1435ACS | 功能描述:IC REG CTRLR BUCK PWM CM 16-SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:4,500 系列:PowerWise® PWM 型:控制器 輸出數:1 頻率 - 最大:1MHz 占空比:95% 電源電壓:2.8 V ~ 5.5 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:6-WDFN 裸露焊盤 包裝:帶卷 (TR) 配用:LM1771EVAL-ND - BOARD EVALUATION LM1771 其它名稱:LM1771SSDX |
發布緊急采購，3分鐘左右您將得到回復。