- 您現在的位置：買賣IC網 > PDF目錄377750 > LTC1479CG (LINEAR TECHNOLOGY CORP) Low-Power LinCMOS(TM) Dual Comparator 10-CFP -55 to 125 PDF資料下載
參數資料
| 型號： | LTC1479CG |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | Low-Power LinCMOS(TM) Dual Comparator 10-CFP -55 to 125 |
| 中文描述： | 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO36 |
| 封裝： | 0.209 INCH, PLASTIC, SSOP-36 |
| 文件頁數： | 6/24頁 |
| 文件大?。?/td> | 466K |
| 代理商： | LTC1479CG |
6
LTC1479
PI
FU
CTIO
N
S
U
U
External Power Supply Pins
DCIN (Pin 1):
Supply Input. A 330
resistor should be
put in series with this pin and the external DC power
source. A 0.1
μ
F bypass capacitor should be connected to
this pin as close as possible.
DCDIV (Pin 2):
Supply Divider Input. This is a high
impedance comparator input with a 1.215V threshold
(rising edge) and approximately –35mV hysteresis.
BAT1, BAT2 (Pins 35, 34):
Supply Input. These two pins
are the inputs from the two batteries. A 1
μ
F bypass
capacitor should be connected to each pin as close as
possible if there is no larger battery supply capacitor
within 2".
V
BAT
(Pin 32):
Battery Voltage Sense. This pin connects
the top of the battery resistor ladder to either BAT1 or
BAT2.
BDIV (Pin 33):
Battery Divider Input. A high impedance
comparator input with a 1.215V threshold (falling edge)
and approximately 35mV hysteresis.
V
BKUP
(Pin 36):
Supply Input. This input supplies power to
the LTC1479 when in the backup mode of operation. A 1
μ
F
bypass capacitor should be connected to the V
BKUP
pin as
close as possible if there is no larger backup supply
capacitor within 2".
Internal Power Supply Pins
V
CCP
(Pin 20):
Power Supply Output. Bypass this output
with at least a 0.1
μ
F capacitor. The V
CCP
power supply is
used primarily to power internal logic circuitry.
V
CC
(Pin 15):
Power Supply Output. This is a nominal
3.60V output. Bypass this regulator output with a 2.2
μ
F
tantalum capacitor. This capacitor s required for stability.
V
+
(Pin 17):
Supply. The V
+
pin is connected via three
internal diodes to the DCIN, BAT1 and BAT2 pins and
powers the top of the V
GG
switching regulator inductor.
Bypass this pin with a 1
μ
F/35V capacitor.
V
GG
(Pin 16):
Gate Supply.
This high voltage (36.5V)
switching regulator is intended only for driving the internal
micropower gate drive circuitry. Do not load this pin with
any external circuitry.Bypass this pin with a 1
μ
F/50V
capacitor.
SW (Pin 18):
Output.
This pin drives the “bottom” of the
V
GG
switching regulator inductor which is connected
between this pin and the V
+
pin.
GND (Pin 19):
Ground.
The V
GG
and V
+
bypass capacitors
should be returned to this ground which is connected
directly to the source of the N-channel switch in the V
GG
regulator.
Input Power Switches
GA, GB (Pins 4, 6):
DCIN Switch Gate Drive.
These two
pins drive the gates of the back-to-back N-channel switches
in series with the DCIN input.
SAB (Pin 5):
Source Return. The SAB pin is connected to
the sources of SW A and SW B. A small pull-down current
source returns this node to 0V when the switches are
turned off.
GC, GD (Pins 7, 9):
BAT1 Switch Gate Drive.
These two
pins drive the gates of the back-to-back N-channel
switches in series with the BAT1 input.
SCD (Pin 8):
Source Return.
The SCD pin is connected to
the sources of SW C and SW D. A small pull-down current
source returns this node to 0V when the switches are
turned off.
GE, GF (Pins 10, 12):
BAT2 Switch Gate Drive.
These two
pins drive the gates of the back-to-back N-channel
switches in series with the BAT2 input.
SEF (Pin 11):
Source Return.
The SEF pin is connected to
the sources of SW E and SW F. A small pull-down current
source returns this node to 0V potential when the switches
are turned off.
SENSE
+
(Pin 13):
Inrush Current Input. This pin should
be connected directly to the “top” (switch side) of the low
valued resistor in series with the three input power
selector switch pairs, SW A/B, SW C/D and SW E/F, for
detecting and controlling the inrush current into and out
of the power supply sources and the output capacitor.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1479IG | PowerPath Controller for Dual Battery Systems |
| LTC1480C | Quad General Purpose LinCMOS(TM) Differential Comparator 14-SOIC |
| LTC1480IN8 | 3.3V Ultra-Low Power RS485 Transceiver |
| LTC1480CS8 | 3.3V Ultra-Low Power RS485 Transceiver |
| LTC1480CN8 | Quad General Purpose LinCMOS(TM) Differential Comparator 14-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1479CG#PBF | 功能描述:IC CTRLR DUAL BATT SYS 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC1479CG#TR | 功能描述:IC CTRLR POWERPATH BATT 36SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LTC1479CG#TRPBF | 功能描述:IC CTRLR DUAL BATT SYS 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LTC1479IG | 功能描述:IC CNTRLR FORDUAL BATTSYS 36SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LTC1479IG#PBF | 功能描述:IC CNTRLR FORDUAL BATTSYS 36SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
發布緊急采購，3分鐘左右您將得到回復。