- 您現在的位置：買賣IC網 > PDF目錄377750 > LTC1479IG (LINEAR TECHNOLOGY CORP) PowerPath Controller for Dual Battery Systems PDF資料下載
參數資料
| 型號： | LTC1479IG |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | 電源管理 |
| 英文描述： | PowerPath Controller for Dual Battery Systems |
| 中文描述： | 3-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO36 |
| 封裝： | 0.209 INCH, PLASTIC, SSOP-36 |
| 文件頁數： | 7/24頁 |
| 文件大?。?/td> | 466K |
| 代理商： | LTC1479IG |
7
LTC1479
PI
FU
CTIO
N
S
U
U
SENSE
–
(Pin 14):
Inrush Current Input.
This pin should
be connected directly to the “bottom” (output side) of the
low valued resistor in series with the three input power
selector switch pairs, SW A/B, SW C/D and SW E/F, for
detecting and controlling the inrush current into and out
of the power supply sources and the output capacitor.
Battery Charging Switches
GG, GH (Pins 29, 27):
Charger Switch Gate Drive. These
two pins drive the gates of the back-to-back N-channel
switch pairs, SW G and SW H, between the charger output
and the two batteries.
SG, SH (Pin 28, 26):
Source Returns.
These two pins are
connected to the sources of SW G and SW H respectively.
A small pull-down current source returns these nodes to
0V when the switches are turned off.
CHGMON (Pin 31):
Battery Selector Output.
This pin is
the output of an internal switch which is connected to
BAT1 and BAT2 and connects the positive terminal of the
selected battery to the voltage feedback resistors in the
charger circuit.
Microprocessor Interface
DCINGOOD (Pin 25):
Comparator Output.
This open-drain
output has an internal 2
μ
A pull-up current source con-
nected through a diode to the V
CCP
power supply. An
external pull-up resistor can be added if more pull-up
current is required. This output is active high when the DC
supply rises above the programmed voltage.
LOBAT (Pin 3):
Comparator Output. This open-drain out-
put does not have an internal pull-up current source and
is active low when the selected battery voltage drops
below the programmed voltage.
DCIN/BAT (Pin 24):
Selector Input. This high impedance
logic input allows the
μ
P to make the ultimate decision on
the connection of the DC power source, based upon the
DCINGOOD pin information. In some minimized systems,
the DCIN/BAT pin may be connected directly to the
DCINGOOD pin.
BATDIS (Pin 23):
Battery Disconnect Input. This high-
impedance logic input has a built-in 2
μ
A pull-up current
source and allows the
μ
P to disconnect the battery from
the system.
3DM (Pin 22):
Three Diode Mode Input. This high imped-
ance logic input has no built-in pull-up current source.
Connect a 100k resistor from this pin to ground to ensure
three diode mode operation from a “cold start.”
CHGSEL (Pin 21):
Battery Charger Selector Input. This
high impedance logic input has a built-in 2
μ
A pull-up
current source and allows the
μ
P to determine which
battery is being charged by connecting the selected
battery to the charger output via one of the switch pairs,
SW G or SW H. (The charger voltage feedback ladder is
simultaneously switched to the selected battery.)
BATSEL (Pin 30):
Battery Selector Input. This high imped-
ance logic input has a built-in 2
μ
A pull-up current source
and allows the
μ
P to select which battery is connected to
the system and the battery monitor comparator input.
Battery 1 is selected with a logic high on this input and
battery 2 is selected with a logic low.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1480C | Quad General Purpose LinCMOS(TM) Differential Comparator 14-SOIC |
| LTC1480IN8 | 3.3V Ultra-Low Power RS485 Transceiver |
| LTC1480CS8 | 3.3V Ultra-Low Power RS485 Transceiver |
| LTC1480CN8 | Quad General Purpose LinCMOS(TM) Differential Comparator 14-SOIC |
| LTC1480I | Quad General Purpose LinCMOS(TM) Differential Comparator 14-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1479IG#PBF | 功能描述:IC CNTRLR FORDUAL BATTSYS 36SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC1479IG#TR | 功能描述:IC CTRLR POWERPATH BATT 36SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LTC1479IG#TRPBF | 功能描述:IC CTRLR DUAL BATT SYS 36-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 功能:電池監控器 電池化學:堿性，鋰離子，鎳鎘，鎳金屬氫化物 電源電壓:1 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-6 包裝:帶卷 (TR) |
| LTC1480CN8 | 功能描述:IC TXRX 3.3V RS485 LOWPWR 8-DIP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:27 系列:- 類型:收發器 驅動器/接收器數:3/3 規程:RS232，RS485 電源電壓:4.75 V ~ 5.25 V 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC 包裝:管件 |
| LTC1480CN8#PBF | 功能描述:IC TXRX 3.3V RS485 LOWPWR 8-DIP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
發布緊急采購，3分鐘左右您將得到回復。