參數資料
| 型號： | LTC1556IGN#TR |
| 廠商： | Linear Technology |
| 文件頁數： | 10/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LEVEL XLATOR/SIM PS 20SSOP |
| 標準包裝： | 2,500 |
| 邏輯功能： | 電平移位器 |
| 位數： | 1 |
| 輸入類型： | 電壓 |
| 輸出類型： | 電壓 |
| 通道數： | 1 |
| 輸出/通道數目： | 1 |
| 差分 - 輸入:輸出： | 無/無 |
| 傳輸延遲（最大）： | 18ns |
| 電源電壓： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 20-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 帶卷 (TR) |
7
LTC1555/LTC1556
The LTC1555/LTC1556 perform the two primary func-
tions necessary for 3V controllers (e.g., GSM cellular
telephone controllers, smart card readers, etc.) to com-
municate with 5V SIMs or smart cards. They produce a
regulated 5V VCC supply for the SIM and provide level
translators for communication between the SIM and the
controller.
VCC Voltage Regulator
The regulator section of the LTC1555/LTC1556 (refer to
the Block Diagram) consists of a step-up/step-down charge
pump DC/DC converter. The charge pump can operate
over a wide input voltage range (2.7V to 10V) while
maintaining a regulated VCC output. The wide VIN range
enables the parts to be powered directly from a battery (if
desired) rather than from a 3V DC/DC converter output.
When VIN is less than the desired VCC the parts operate as
switched capacitor voltage doublers. When VIN is greater
than VCC the parts operate as gated switch step-down
converters. In either case, voltage conversion requires
only one small flying capacitor and output capacitor.
The VCC output can be programmed to either 5V or 3V via
the M0 and M1 mode pins. This feature is useful in
applications where either a 5V or 3V SIM may be used. The
charge pump VCC output may also be connected directly to
VIN if desired. When the charge pump is put into shutdown
(M0, M1 = 0), VCC is pulled to GND via an internal switch
to aid in proper system supply sequencing.
The soft start feature limits inrush currents upon start-up
or coming out of shutdown mode. When the SS pin is tied
to GND, the soft start feature is enabled. This limits the ef-
fective inrush current out of VIN to approximately 25mA
(COUT = 10F). Inrush current limiting is especially useful
when powering the LTC1555/LTC1556 from a 3V DC/DC
output since the unlimited inrush current may approach
200mA and cause voltage transients on the 3V supply. How-
ever, in cases where fast turn-on time is desired, the soft
start feature may be overridden by tying the SS pin to DVCC.
APPLICATIONS INFORMATION
WU
U
Capacitor Selection
For best performance, it is recommended that low ESR
(< 0.5
)capacitorsbeusedforbothCINandCOUTtoreduce
noise and ripple. The CIN and COUT capacitors should be
either ceramic or tantalum and should be 10
F or greater
(ceramic capacitors will produce the smallest output ripple).
If the input source impedance is very low (< 0.5
),CINmay
not be needed. Increasing the size of COUTto22Forgreater
will reduce output voltage ripple—particularly with high VIN
voltages (8V or greater). A ceramic capacitor is recom-
mended for the flying capacitor C1 with a value of 0.1
F or
0.22
F.
Output Ripple
Normal LTC1555/LTC1556 operation produces voltage
ripple on the VCC pin. Output voltage ripple is required for
the parts to regulate. Low frequency ripple exists due to
the hysteresis in the sense comparator and propagation
delays in the charge pump enable/disable circuits. High
frequency ripple is also present mainly from the ESR
(equivalent series resistance) in the output capacitor.
Typical output ripple (VIN < 8V) under maximum load is
75mV peak-to-peak with a low ESR, 10
F output capaci-
tor. For applications requiring VIN to exceed 8V, a 22F or
larger COUT capacitor is recommended to maintain maxi-
mum ripple in the 75mV range.
The magnitude of the ripple voltage depends on several
factors. High input voltages increase the output ripple
since more charge is delivered to COUT per charging cycle.
A large C1 flying capacitor (> 0.22
F) also increases ripple
in step-up mode for the same reason. Large output current
load and/or a small output capacitor (< 10
F) results in
higher ripple due to higher output voltage dV/dt. High ESR
capacitors (ESR > 0.5
) on the output pin cause high
frequency voltage spikes on VOUT with every clock cycle.
A 10
F ceramic capacitor on the VCC pin should produce
acceptable levels of output voltage ripple in nearly all
applications. However, there are several ways to further
相關PDF資料 |
PDF描述 |
|---|---|
| SY100ELT982KG TR | IC TRANSLATOR PECL-CML 10-MSOP |
| V24B12M200BF | CONVERTER MOD DC/DC 12V 200W |
| V24B12M200BL3 | CONVERTER MOD DC/DC 12V 200W |
| ICS181M-53 | IC CLOCK GEN LOW EMI 8-SOIC |
| V24B12M200BL | CONVERTER MOD DC/DC 12V 200W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1558CGN-3.3 | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監(jiān)控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| LTC1558CGN-3.3#PBF | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| LTC1558CGN-3.3#TRPBF | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
| LTC1558CGN-5 | 功能描述:IC BACKUP BATT CNTRLR 5V 16-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監(jiān)控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| LTC1558CGN-5#PBF | 功能描述:IC BACKUP BATT CNTRLR 5V 16-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
發(fā)布緊急采購，3分鐘左右您將得到回復。