- 您現在的位置：買賣IC網 > PDF目錄8991 > LTC1556IGN (Linear Technology)IC LEVEL TRANSLTOR W/LDO 20SSOP PDF資料下載
參數資料
| 型號： | LTC1556IGN |
| 廠商： | Linear Technology |
| 文件頁數： | 8/12頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LEVEL TRANSLTOR W/LDO 20SSOP |
| 標準包裝： | 55 |
| 邏輯功能： | 電平移位器 |
| 位數： | 1 |
| 輸入類型： | 電壓 |
| 輸出類型： | 電壓 |
| 通道數： | 1 |
| 輸出/通道數目： | 1 |
| 差分 - 輸入:輸出： | 無/無 |
| 傳輸延遲（最大）： | 18ns |
| 電源電壓： | 1.8 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 20-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 20-SSOP |
| 包裝： | 管件 |
5
LTC1555/LTC1556
LTC1555/LTC1556
CIN (Pin 1): Clock Input Pin from Controller.
RIN (Pin 2): Reset Input Pin from Controller.
DATA (Pin 3): Controller Side Data Input/Output Pin. Can
be used for single pin bidirectional data transfer between
the controller and the SIM card as long as the controller
data pin is open drain. The controller output must be able
to sink 1mA max when driving the DATA pin low due to
the internal pull-up resistors on the DATA and I/O pins. If
the controller data output is not open drain, then the
DDRV pin should be used for sending data to the SIM
card and the DATA pin used for receiving data from the
SIM card (see Figure 1).
DDRV (Pin 4): Optional Data Input Pin for Sending Data
to the SIM card. When not needed, the DDRV pin should
be left floating or tied to DVCC (an internal 1A current
source will pull the DDRV pin up to DVCC if left floating).
DVCC (Pins 5/7): Supply Voltage for Controller Side Digital
I/O Pins. May be between 1.8V and 5.5V (typically 3V).
SS (Pins 6/8): Soft Start Enable Pin. A logic low will
enable the charge pump inrush current limiting feature.
A logic high will disable the soft start feature and allow
VCC to be ramped as quickly as possible upon start-up
and coming out of shutdown.
M1 (Pins 7/9): Mode Control Bit 1 (see Truth Table).
M0 (Pins 8/10): Mode Control Bit 0 (see Truth Table).
This table defines the various operating modes that may
be obtained via the M0 and M1 mode control pins.
Truth Table
M0
M1
MODE
0V
Shutdown (VCC = 0V)
0V
DVCC
VCC = VIN
DVCC
0V
VCC = 3V
DVCC
VCC = 5V
GND (Pins 9/11, 12): Ground for Both the SIM and the
Controller. Should be connected to the SIM GND contact
as well as to the VIN/Controller GND. Proper grounding
and supply bypassing is required to meet 10kV ESD
specifications.
C1– (Pins 10/12): Charge Pump Flying Capacitor Nega-
tive Input.
C1+ (Pins 11/13): Charge Pump Flying Capacitor Positive
Input.
VIN (Pins 12/14): Charge Pump Input Voltage Pin. Input
voltage range is 2.7V to 10V. Connect a 10
F low ESR
input bypass capacitor close to the VIN pin.
VCC (Pins 13/15): SIM Card VCC Output. This pin should
be connected to the SIM VCC contact. The VCC output
voltage is determined by the M0 and M1 pins (see Truth
Table). VCC is discharged to GND during shutdown
(M0, M1 = 0V). A 10
F low ESR output capacitor should
connect close to the VCC pin.
I/O (Pins 14/18): SIM Side I/O Pin. The pin is an open
drain output with a nominal pull-up resistance of 10k and
should be connected to the SIM I/O contact. The SIM card
must sink up to 1mA max when driving the I/O pin low
due to the internal pull-up resistors on the I/O and DATA
pins. The I/O pin is held active low when the part is in
shutdown.
RST (Pins 15/19): Level Shifted Reset Output Pin. Should
be connected to the SIM RST contact.
CLK (Pins 16/20): Level Shifted Clock Output Pin. Should
be connected to the SIM CLK contact. Careful trace
routing is recommended due to fast rise and fall edge
speeds.
PIN FUNCTIONS
UU
U
相關PDF資料 |
PDF描述 |
|---|---|
| VI-24F-MY-F2 | CONVERTER MOD DC/DC 72V 50W |
| ADG3123BRUZ | IC XLATOR 8CH LOG-HV 20-TSSOP |
| VI-24D-MY-F4 | CONVERTER MOD DC/DC 85V 50W |
| LTC1045CN#PBF | IC TRANSLATOR/RCVR/DVR HEX 20DIP |
| VI-24D-MY-F3 | CONVERTER MOD DC/DC 85V 50W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1556IGN#PBF | 功能描述:IC LEVEL TRANSLTOR W/LDO 20SSOP RoHS:是 類別:集成電路 (IC) >> 邏輯 - 變換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:100 系列:- 邏輯功能:變換器，雙向 位數:2 輸入類型:CMOS 輸出類型:CMOS 數據速率:16Mbps 通道數:2 輸出/通道數目:1 差分 - 輸入:輸出:無/無 傳輸延遲（最大）:15ns 電源電壓:1.65 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:10-UFQFN 供應商設備封裝:10-UTQFN（1.4x1.8） 包裝:管件 |
| LTC1556IGN#TR | 功能描述:IC LEVEL XLATOR/SIM PS 20SSOP RoHS:否 類別:集成電路 (IC) >> 邏輯 - 變換器 系列:- 產品培訓模塊:Logic Packages 標準包裝:2,500 系列:- 邏輯功能:變換器，雙向 位數:2 輸入類型:電壓 輸出類型:電壓 數據速率:- 通道數:2 輸出/通道數目:1 差分 - 輸入:輸出:無/無 傳輸延遲（最大）:1.5ns 電源電壓:3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-TSSOP 包裝:帶卷 (TR) 其它名稱:935284857118GTL2002DP/S440-TGTL2002DP/S440-T-ND |
| LTC1556IGN#TRPBF | 功能描述:IC LEVEL TRANSLTOR W/LDO 20SSOP RoHS:是 類別:集成電路 (IC) >> 邏輯 - 變換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:100 系列:- 邏輯功能:變換器，雙向 位數:2 輸入類型:CMOS 輸出類型:CMOS 數據速率:16Mbps 通道數:2 輸出/通道數目:1 差分 - 輸入:輸出:無/無 傳輸延遲（最大）:15ns 電源電壓:1.65 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 封裝/外殼:10-UFQFN 供應商設備封裝:10-UTQFN（1.4x1.8） 包裝:管件 |
| LTC1558CGN-3.3 | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:2,000 系列:Impedance Track™ 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.4 V ~ 2.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:帶卷 (TR) 產品目錄頁面:1020 (CN2011-ZH PDF) 配用:BQ27350EVM-ND - BQ27350EVM 其它名稱:296-21665-2 |
| LTC1558CGN-3.3#PBF | 功能描述:IC BACKUP BATT CNTRLR3.3V 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:1 系列:- 功能:充電管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:3.75 V ~ 6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:SC-74A，SOT-753 供應商設備封裝:SOT-23-5 包裝:剪切帶 (CT) 產品目錄頁面:669 (CN2011-ZH PDF) 其它名稱:MCP73831T-2ACI/OTCT |
發布緊急采購，3分鐘左右您將得到回復。