- 您現在的位置：買賣IC網 > PDF目錄10301 > LTC1594LCS#PBF (Linear Technology)IC A/D CONV 12BIT SRL 4CH 16SOIC PDF資料下載
參數資料
| 型號： | LTC1594LCS#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 9/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC A/D CONV 12BIT SRL 4CH 16SOIC |
| 標準包裝： | 50 |
| 位數： | 12 |
| 采樣率（每秒）： | 10.5k |
| 數據接口： | MICROWIRE?，QSPI?，串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 1.6mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-SOIC |
| 包裝： | 管件 |
| 輸入數目和類型： | 8 個單端，單極 |
17
LTC1594L/LTC1598L
15948lfb
Input Leakage Current
Input leakage currents can also create errors if the source
resistance gets too large. For instance, the maximum
input leakage specification of 200nA (at 85
°C) flowing
through a source resistance of 600
will cause a voltage
drop of 120
V or 0.2LSB. This error will be much
reduced at lower temperatures because leakage drops
rapidly (see typical curve Input Channel Leakage Current
vs Temperature).
REFERENCE INPUTS
The reference input of the LTC1594L/LTC1598L is effec-
tively a 50k resistor from the time CS goes low to the end
of the conversion. The reference input becomes a high
impedance node at any other time (see Figure 9). Since
the voltage on the reference input defines the voltage
span of the A/D converter, the reference input should be
driven by a reference with low ROUT (ex. LT1004, LT1019
and LT1021) or a voltage source with low ROUT.
Reduced Reference Operation
The effective resolution of the LTC1594L/LTC1598L can
be increased by reducing the input span of the convert-
ers. The LTC1594L/LTC1598L exhibit good linearity and
gain over a wide range of reference voltages (see typical
curves Change in Linearity vs Reference Voltage and
Change in Gain vs Reference Voltage). However, care
must be taken when operating at low values of VREF
because of the reduced LSB step size and the resulting
higher accuracy requirement placed on the converters.
The following factors must be considered when operat-
ing at low VREF values:
1. Offset
2. Noise
3. Conversion speed (CLK frequency)
Offset with Reduced VREF
The offset of the LTC1594L/LTC1598L has a larger effect
on the output code when the ADCs are operated with
reduced reference voltage. The offset (which is typically
a fixed voltage) becomes a larger fraction of an LSB as the
size of the LSB is reduced. The typical curve of Change in
Offset vs Reference Voltage shows how offset in LSBs is
related to reference voltage for a typical value of VOS. For
example, a VOS of 122V which is 0.2LSB with a 2.5V
reference becomes 0.5LSB with a 1V reference and
2.5LSBs with a 0.2V reference. If this offset is unaccept-
able, it can be corrected digitally by the receiving system
or by offsetting the “COM” input of the LTC1594L/
LTC1598L.
Noise with Reduced VREF
The total input referred noise of the LTC1594L/LTC1598L
can be reduced to approximately 400
V peak-to-peak
using a ground plane, good bypassing, good layout
techniques and minimizing noise on the reference inputs.
This noise is insignificant with a 5V reference but will
become a larger fraction of an LSB as the size of the LSB
is reduced.
For operation with a 2.5V reference, the 400
V noise is
only 0.66LSB peak-to-peak. In this case, the LTC1594L/
LTC1598L noise will contribute virtually no uncertainty to
the output code. However, for reduced references the
noise may become a significant fraction of an LSB and
cause undesirable jitter in the output code. For example,
with a 1.25V reference this same 400
V noise is 1.32LSB
peak-to-peak. This will reduce the range of input voltages
over which a stable output code can be achieved by 1LSB.
If the reference is further reduced to 1V, the 400
V noise
becomes equal to 1.65LSBs and a stable code may be
difficult to achieve. In this case, averaging multiple
readings may be necessary.
This noise data was taken in a very clean setup. Any setup
induced noise (noise or ripple on VCC, VREF or VIN) will
add to the internal noise. The lower the reference voltage
to be used the more critical it becomes to have a clean,
noise free setup.
LTC1594L
LTC1598L
REF+
ROUT
VREF
1
4
GND
1594L/98L F09
Figure 9. Reference Input Equivalent Circuit
APPLICATIONS INFORMATION
WU
U
相關PDF資料 |
PDF描述 |
|---|---|
| MS27474T14F18SD | CONN RCPT 18POS JAM NUT W/SCKT |
| LTC1594LCS | IC A/D CONV 12BIT SRL 4CH 16SOIC |
| MS27468E17F26S | CONN RCPT 26POS JAM NUT W/SCKT |
| D38999/26WE6BA | CONN HSG PLUG 6POS STRGHT SCKT |
| LTC1594CS | IC A/D CONV 12BIT SRL 4CH 16SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1594LIS | 功能描述:IC A/D CONV 12BIT SRL 4CH 16SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1594LIS#PBF | 功能描述:IC A/D CONV 12BIT SRL 4CH 16SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| LTC1594LIS#TR | 功能描述:IC ADC 12BIT 3V 4CH SAMPL 16SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1594LIS#TRPBF | 功能描述:IC A/D CONV 12BIT SRL 4CH 16SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1595ACN8 | 功能描述:IC D/A CONV 16BIT MULTPLYNG 8DIP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
發(fā)布緊急采購，3分鐘左右您將得到回復。