- 您現在的位置：買賣IC網 > PDF目錄377754 > LTC1598LCG (LINEAR TECHNOLOGY CORP) Replaced by ADS7961 : 8-Bit, 76 kSPS ADC Serial Out, On-Chip 20 Ch. Analog Mux, 19 Ch. 28-PLCC PDF資料下載
參數資料
| 型號： | LTC1598LCG |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | Replaced by ADS7961 : 8-Bit, 76 kSPS ADC Serial Out, On-Chip 20 Ch. Analog Mux, 19 Ch. 28-PLCC |
| 中文描述： | 8-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO24 |
| 封裝： | 0.209 INCH, PLASTIC, SSOP-24 |
| 文件頁數： | 16/24頁 |
| 文件大小： | 278K |
| 代理商： | LTC1598LCG |
16
LTC1594L/LTC1598L
APPLICATIO
S I
FOR
ATIO
U
edge, the S & H goes into hold mode and the conversion
begins. The voltage on the “COM” input must remain
constant and be free of noise and ripple throughout the
conversion time. Otherwise, the conversion operation
may not be performed accurately. The conversion time is
12 CLK cycles. Therefore, a change in the “COM” input
voltage during this interval can cause conversion errors.
For a sinusoidal voltage on the “COM” input this error
would be:
V
ERROR(MAX)
= V
PEAK
(2
π
)(f)(“COM”)12/f
CLK
Where f(“COM”) is the frequency of the “COM” input
voltage, V
PEAK
is its peak amplitude and f
CLK
is the
frequency of the CLK. In most cases, V
ERROR
will not be
significant. For a 60Hz signal on the “COM” input to
generate a 0.5LSB error (305
μ
V) with the converter
running at CLK = 200kHz, its peak value would have to be
5.266mV.
W
U
U
ANALOG INPUTS
Because of the capacitive redistribution A/D conversion
techniques used, the analog inputs of the LTC1594L/
LTC1598L have capacitive switching input current spikes.
These current spikes settle quickly and do not cause a
problem. However, if large source resistances are used
or if slow settling op amps drive the inputs, care must be
taken to insure that the transients caused by the current
spikes settle completely before the conversion begins.
“Analog” Input Settling
The input capacitor of the LTC1594L/LTC1598L is switched
onto the selected channel input during the t
SMPL
time (see
Figure 7) and samples the input signal within that time. The
sample phase is at least 1 1/2 CLK cycles before conver-
sion starts. The voltage on the “analog” input must settle
completely within t
SMPL
. Minimizing R
SOURCE+
and C1 will
improve the input settling time. If a large “analog” input
source resistance must be used, the sample time can be
increased by using a slower CLK frequency.
“COM” Input Settling
At the end of the t
SMPL
, the input capacitor switches to the
“COM” input and conversion starts (see Figures 1 and 7).
During the conversion, the “analog” input voltage is
effectively “held” by the sample-and-hold and will not
affect the conversion result. However, it is critical that the
“COM” input voltage settles completely during the first
CLK cycle of the conversion time and be free of noise.
Minimizing R
SOURCE–
and C2 will improve settling time.
If a large “COM” input source resistance must be used,
the time allowed for settling can be extended by using a
slower CLK frequency.
Input Op Amps
When driving the analog inputs with an op amp it is
important that the op amp settle within the allowed time
(see Figure 7). Again, the “analog” and “COM” input
sampling times can be extended as described above to
accommodate slower op amps. Most op amps, including
the LT
1006 and LT1413 single supply op amps, can be
made to settle well even with the minimum settling
windows of 7.5
μ
s (“analog” input) which occur at the
maximum clock rate of 200kHz.
Source Resistance
The analog inputs of the LTC1594L/LTC1598L look like a
20pF capacitor (C
IN
) in series with a 1k resistor (R
ON
) and
a 90
channel resistance as shown in Figure 8. C
IN
gets
switched between the selected “analog” and “COM”
inputs once during each conversion cycle. Large external
source resistors and capacitances will slow the settling
of the inputs. It is important that the overall RC time
constants be short enough to allow the analog inputs to
completely settle within the allowed time.
Figure 8. Analog Input Equivalent Circuit
R
ON
1k
R
ON
90
C
20pF
LTC1594L
LTC1598L
“ANALOG”
INPUT
R
SOURCE
+
V
IN
+
C1
“COM”
INPUT
MUXOUT
MUX
ADCIN
R
SOURCE
–
V
IN
–
C2
1594L/98L F08
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1594L | 4- Channel, 3V Micropower Sampling 12-Bit Serial I/O A/D Converters(四通道,3V微功耗采樣12位串行輸入/輸出模數轉換器) |
| LTC1594 | 8-Bit, 40 kSPS ADC Serial-Out, On-Chip 12-Ch. Analog Mux, 11 Ch. 20-SOIC |
| LTC1598IG | 4- and 8-Channel, Micropower Sampling 12-Bit Serial I/O A/D Converters |
| LTC1594CS | 4- and 8-Channel, Micropower Sampling 12-Bit Serial I/O A/D Converters |
| LTC1594IS | 4- and 8-Channel, Micropower Sampling 12-Bit Serial I/O A/D Converters |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1598LCG#PBF | 功能描述:IC A/D CONV 12BIT SRL 8CH 24SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC1598LCG#TR | 功能描述:IC ADC 12BIT 3V 8CH SAMPL 24SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1598LCG#TRPBF | 功能描述:IC A/D CONV 12BIT SRL 8CH 24SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1598LIG | 功能描述:IC A/D CONV 12BIT SRL 8CH 24SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC1598LIG#PBF | 功能描述:IC A/D CONV 12BIT SRL 8CH 24SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。