- 您現在的位置：買賣IC網 > PDF目錄377757 > LTC1606IG (LINEAR TECHNOLOGY CORP) 16-Bit, 250ksps, Single Supply ADC PDF資料下載
參數資料
| 型號： | LTC1606IG |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 16-Bit, 250ksps, Single Supply ADC |
| 中文描述： | 1-CH 16-BIT SUCCESSIVE APPROXIMATION ADC, PARALLEL ACCESS, PDSO28 |
| 封裝： | 0.209 INCH, PLASTIC, SSOP-28 |
| 文件頁數： | 11/12頁 |
| 文件大?。?/td> | 169K |
| 代理商： | LTC1606IG |
11
LTC1606
Output Data
The output data can be read as a 16-bit word or it can be
read as two 8-bit bytes. The format of the output data is
two’s complement. The digital input pin BYTE is used to
control the two byte read. With the BYTE pin low, the first
eight MSBs are output on the D15 to D8 pins and the eight
LSBs are output on the D7 to D0 pins. When the BYTE pin
is taken high, the eight LSBs replace the eight MSBs
(Figure 10).
Dynamic Performance
FFT (Fast Fourier Transform) test techniques are used to
test the ADC’s frequency response, distortion and noise at
the rated throughput. By applying a low distortion sine
wave and analyzing the digital output using an FFT algo-
rithm, the ADC’s spectral content can be examined for
frequencies outside the fundamental.
Signal-to-Noise Ratio
The Signal-to-Noise and Distortion Ratio (SINAD) is the
ratio between the RMS amplitude of the fundamental input
frequency to the RMS amplitude of all other frequency
components at the A/D output. The output is band limited
to frequencies from above DC and below half the sampling
frequency. A typical LTC1606 has a SINAD of 90dB and
THD of –102dB with a 250kHz sampling rate and a 1kHz
input.
Total Harmonic Distortion
Total Harmonic Distortion (THD) is the ratio of the RMS
sum of all harmonics of the input signal to the fundamental
itself. The out-of-band harmonics alias into the frequency
band between DC and half the sampling frequency. THD is
expressed as:
THD = 20log
√
V
22
+ V
32
+ V
42
... + V
N2
V
1
where V
1
is the RMS amplitude of the fundamental fre-
quency and V
2
through V
N
are the amplitudes of the
second through Nth harmonics.
Board Layout, Power Supplies and Decoupling
Wire wrap boards and molded sockets are not recom-
mended for high resolution or high speed A/D converters.
To obtain the best performance from the LTC1606, a
printed circuit board is required. Layout for the printed
circuit board should ensure the digital and analog signal
lines are separated as much as possible. In particular, care
should be taken not to run any digital track alongside an
analog signal track or underneath the ADC. The analog
input should be screened by AGND.
Pay particular attention to the design of the analog and
digital ground planes. The DGND pin of the LTC1606
should be tied to the analog ground plane. Placing the
bypass capacitor as close as possible to the power supply,
the reference and reference buffer output is very impor-
tant. Low impedance common returns for these bypass
capacitors are essential to low noise operation of the ADC,
and the foil width for these tracks should be as wide as
possible. Also, since any potential difference in grounds
between the signal source and ADC appears as an error
voltage in series with the input signal, attention should be
paid to reducing the ground circuit impedance as much as
possible.
APPLICATIO
S I
N
FOR
ATIO
U
W
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1606ACG | 16-Bit, 250ksps, Single Supply ADC |
| LTC1606AI | 16-Bit, 250ksps, Single Supply ADC |
| LTC1606AIG | 16-Bit, 250ksps, Single Supply ADC |
| LTC1606C | 16-Bit, 250ksps, Single Supply ADC |
| LTC1606CG | 16-Bit, 250ksps, Single Supply ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1606IG#PBF | 功能描述:IC A/D CONV 16BIT SAMPLNG 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1606IG#TR | 功能描述:IC ADC 16BIT 5V SAMPLING 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1606IG#TRPBF | 功能描述:IC A/D CONV 16BIT SAMPLNG 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1606ISW | 功能描述:IC ADC 16BIT 5V SAMPLING 28SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC1606ISW#PBF | 功能描述:IC A/D CONV 16BIT SAMPLNG 28SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。