- 您現在的位置：買賣IC網 > PDF目錄377757 > LTC1624CS (Linear Technology Corporation) Isolated Flyback Switching Regulator with 9V Output PDF資料下載
參數資料
| 型號： | LTC1624CS |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | Isolated Flyback Switching Regulator with 9V Output |
| 中文描述： | 隔離反激式開關穩壓9V輸出 |
| 文件頁數： | 20/28頁 |
| 文件大?。?/td> | 490K |
| 代理商： | LTC1624CS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
20
LTC1624
Positive-to-negative converters have high ripple current in
both the input and output capacitors. For long capacitor
lifetime, the RMS value of this current must be less than
the high frequency ripple rating of the capacitor.
The following formula gives an approximate value for RMS
ripple current. This formula assumes continuous mode
and low current ripple. Small inductors will give somewhat
higher ripple current, especially in discontinuous mode.
For the exact formulas refer to Application Note 44, pages
28 to 30. The input and output capacitor ripple current
(occurring at V
IN(MIN)
) is:
Capacitor
ff I
V
V
OUT
OUT
IN
I
RMS
=
( )(
)
ff = Fudge factor (1.2 to 2.0)
The output peak-to-peak ripple voltage is:
V
OUT(P-P)
= R
ESR
(I
D(MAX)
)
The input capacitor can also see a very high surge current
when a battery is suddenly connected, and solid tantalum
capacitors can fail under this condition. Be sure to specify
surge tested capacitors.
Positive-to-Negative Converter: Duty Cycle
Limitations
The minimum on-time of 450ns sets a limit on how high
of input-to-output ratio can be tolerated while not skipping
cycles. This only impacts designs when very low output
voltages (
V
OUT
< 2.5V) are needed. The maximum input
voltage is:
V
IN(MAX)
< 10.1V
OUT
+ 5V For DC > 9%
V
IN(MAX)
< 36V –
V
OUT
For absolute maximum ratings
Positive-to-Negative Converter: Shutdown
Considerations
Since the ground pin on the LTC1624 is referenced to
–V
OUT
, additional circuitry is needed to put the LTC1624
into shutdown. Shutdown is enabled by pulling the
I
TH
/RUN pin below 0.8V relative to the LTC1624 ground
pin. With the LTC1624 ground pin referenced to –V
OUT
,
the nonimal range on the I
TH
/RUN pin is –V
OUT
(in
shutdown) to (–V
OUT
+ 2.4V)(at Max I
OUT
). Referring to
Figure 15, M2, M3 and R3 provide a level shift from typical
TTL levels to the LTC1624 operating as positive-to-nega-
tive converter. MOSFET M3 supplies gate drive to M2
during shutdown, while M2 pulls the I
TH/RUN
pin voltage to
–V
OUT
, shutting down the LTC1624.
Step-Down Converters: PC Board Layout Checklist
When laying out the printed circuit board, the following
checklist should be used to ensure proper operation of the
LTC1624. These items are also illustrated graphically in
the layout diagram of Figure 9. Check the following in your
layout:
1. Are the signal and power grounds segregated The
LTC1624 ground (Pin 4) must return to the (–) plate
of C
OUT.
2. Does the V
FB
(Pin 3) connect directly to the feedback
resistors The resistive divider R1, R2 must be con-
nected between the (+) plate of C
OUT
and signal ground.
The 100pF capacitor should be as close as possible to
the LTC1624.
3. Does the V
IN
lead connect to the input voltage at the
same point as R
SENSE
and are the SENSE
–
and V
IN
leads
routed together with minimum PC trace spacing The
filter capacitor between V
IN
and SENSE
–
should be as
close as possible to the LTC1624.
4. Does the (+) plate of C
IN
connect to R
SENSE
as closely
as possible This capacitor provides the AC current to
the MOSFET(s). Also, does C
IN
connect as close as
possible to the V
IN
and ground pin of the LTC1624
This capacitor also supplies the energy required to
recharge the bootstrap capacitor. Adequate input
decoupling is critical for proper operation.
5. Keep the switch node SW away from sensitive small-
signal nodes. Ideally, M1, L1 and D1 should be con-
nected as closely as possible at the switch node.
APPLICATIO
S I
FOR
ATIO
U
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1624IS8 | Isolated Flyback Switching Regulator with 9V Output |
| LTC1624CS8 | 8-Bit, 40 kSPS ADC Serial Out, Low Power, Compatible to TLC540/545/1540, Single Ch. 8-SO |
| LTC1624IS | Isolated Flyback Switching Regulator with 9V Output |
| LTC1624 | High Efficiency SO-8 N-Channel Switching Regulator Controller(SO-8封裝，高效率，N溝道開關穩壓控制器) |
| LTC1625C | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1624CS8 | 功能描述:IC REG CTRLR BST FLYBK INV 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1624CS8#PBF | 功能描述:IC REG CTRLR BST FLYBK INV 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 特色產品:LM3753/54 Scalable 2-Phase Synchronous Buck Controllers 標準包裝:1 系列:PowerWise® PWM 型:電壓模式 輸出數:1 頻率 - 最大:1MHz 占空比:81% 電源電壓:4.5 V ~ 18 V 降壓:是 升壓:無 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-5°C ~ 125°C 封裝/外殼:32-WFQFN 裸露焊盤 包裝:Digi-Reel® 產品目錄頁面:1303 (CN2011-ZH PDF) 其它名稱:LM3754SQDKR |
| LTC1624CS8#TR | 功能描述:IC REG CTRLR BST FLYBK INV 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1624CS8#TRPBF | 功能描述:IC REG CTRLR BST FLYBK INV 8SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 穩壓器 - DC DC 切換控制器 系列:- 標準包裝:2,500 系列:- PWM 型:電流模式 輸出數:1 頻率 - 最大:500kHz 占空比:96% 電源電壓:4 V ~ 36 V 降壓:無 升壓:是 回掃:無 反相:無 倍增器:無 除法器:無 Cuk:無 隔離:無 工作溫度:-40°C ~ 125°C 封裝/外殼:24-WQFN 裸露焊盤 包裝:帶卷 (TR) |
| LTC1624CS8PBF | 制造商:Linear Technology 功能描述:LTC1624CS8PBF |
發布緊急采購，3分鐘左右您將得到回復。