- 您現在的位置：買賣IC網 > PDF目錄377758 > LTC1629-PG (Linear Technology Corporation) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | LTC1629-PG |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 抗輻射高效，5安培開關穩壓器 |
| 文件頁數： | 12/28頁 |
| 文件大小： | 330K |
| 代理商： | LTC1629-PG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
12
LTC1629/LTC1629-PG
APPLICATIU
R
SENSE
Selection For Output Current
R
SENSE1, 2
are chosen based on the required output
current. The LTC1629 current comparator has a maxi-
mum threshold of 75mV/R
SENSE
and an input common
mode range of SGND to 1.5( INTV
CC
). The current com-
parator threshold sets the peak inductor current, yielding
a maximum average output current I
MAX
equal to the peak
value less half the peak-to-peak ripple current,
I
L
.
Allowing a margin for variations in the LTC1629 and
external component values yields:
R
SENSE
= (50mV/I
MAX
)N
where N = number of stages.
When using the controller in very low dropout conditions,
the maximum output current level will be reduced due to
internal slope compensation required to meet stability
criterion for buck regulators operating at greater than 50%
duty factor. A curve is provided to estimate this reduction
in peak output current level depending upon the operating
duty factor.
W
U
U
Operating Frequency
The LTC1629 uses a constant frequency, phase-lockable
architecture with the frequency determined by an internal
capacitor. This capacitor is charged by a fixed current plus
an additional current which is proportional to the voltage
applied to the PLLFLTR pin. Refer to Phase-Locked Loop
and Frequency Synchronization in the Applications Infor-
mation section for additional information.
A graph for the voltage applied to the PLLFLTR pin vs
frequency is given in Figure2. As the operating frequency
is increased the gate charge losses will be higher, reducing
efficiency (see Efficiency Considerations). The maximum
switching frequency is approximately 310kHz.
Inductor Value Calculation and Output Ripple Current
The operating frequency and inductor selection are inter-
related in that higher operating frequencies allow the use
of smaller inductor and capacitor values. So why would
anyone ever choose to operate at lower frequencies with
larger components The answer is efficiency. A higher
frequency generally results in lower efficiency because of
MOSFET gate charge and transition losses. In addition to
this basic tradeoff, the effect of inductor value on ripple
current and low current operation must also be consid-
ered. The PolyPhase approach reduces both input and
output ripple currents while optimizing individual output
stages to run at a lower fundamental frequency, enhancing
efficiency.
The inductor value has a direct effect on ripple current. The
inductor ripple current
I
L
per individual section, N,
decreases with higher inductance or frequency and in-
creases with higher V
IN
or V
OUT
:
I
V
fL
V
V
L
OUT
OUT
IN
=
1
where f is the individual output stage operating frequency.
In a PolyPhase converter, the net ripple current seen by the
output capacitor is much smaller than the individual
inductor ripple currents due to the ripple cancellation. The
details on how to calculate the net output ripple current
can be found in Application Note 77.
Figure 3 shows the net ripple current seen by the output
capacitors for the different phase configurations. The
output ripple current is plotted for a fixed output voltage as
the duty factor is varied between 10% and 90% on the
x-axis. The output ripple current is normalized against the
inductor ripple current at zero duty factor. The graph can
be used in place of tedious calculations. As shown in
Figure3, the zero output ripple current is obtained when:
Figure 2. Operating Frequency vs V
PLLFLTR
OPERATING FREQUENCY (kHz)
120
170
220
270
320
P
1629 F02
2.5
2.0
1.5
1.0
0.5
0
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1629CG-PG | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1629 | Dual LinCMOS(TM) Timer 14-SOIC |
| LTC1629C | Dual LinCMOS(TM) Timer 14-SOIC |
| LTC1629C-PG | Dual LinCMOS(TM) Timer 14-SOIC |
| LTC1629CG | Dual LinCMOS(TM) Timer 14-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1642ACGN | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 16.5V 16-Pin SSOP N |
| LTC1642ACGN#PBF | 功能描述:IC CONTROLLER HOTSWAP ADJ 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC1642ACGN#TRPBF | 功能描述:IC CONTROLLER HOTSWAP ADJ 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC1642AIGN | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 16.5V 16-Pin SSOP N |
| LTC1642AIGN#PBF | 功能描述:IC CONTROLLER HOTSWAP ADJ 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。