- 您現在的位置：買賣IC網 > PDF目錄377758 > LTC1629I-PG (Linear Technology Corporation) RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS PDF資料下載
參數資料
| 型號： | LTC1629I-PG |
| 廠商： | Linear Technology Corporation |
| 元件分類： | 基準電壓源/電流源 |
| 英文描述： | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| 中文描述： | 抗輻射高效，5安培開關穩壓器 |
| 文件頁數： | 20/28頁 |
| 文件大?。?/td> | 330K |
| 代理商： | LTC1629I-PG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁當前第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
20
LTC1629/LTC1629-PG
Efficiency Considerations
The percent efficiency of a switching regulator is equal to
the output power divided by the input power times 100%.
It is often useful to analyze individual losses to determine
what is limiting the efficiency and which change would
produce the most improvement. Percent efficiency can be
expressed as:
%Efficiency = 100% – (L1 + L2 + L3 + ...)
where L1, L2, etc. are the individual losses as a percentage
of input power.
Although all dissipative elements in the circuit produce
losses, four main sources usually account for most of the
losses in LTC1629 circuits: 1) LTC1629 V
IN
current (in-
cluding loading on the differential amplifier output),
2) INTV
CC
regulator current, 3) I
2
R losses and 4) Topside
MOSFET transition losses.
1) The V
IN
current has two components: the first is the
DC supply current given in the Electrical Characteristics
table, which excludes MOSFET driver and control cur-
rents; the second is the current drawn from the differential
amplifier output. V
IN
current typically results in a small
(<0.1%) loss.
2) INTV
CC
current is the sum of the MOSFET driver and
control currents. The MOSFET driver current results from
switching the gate capacitance of the power MOSFETs.
Each time a MOSFET gate is switched from low to high to
low again, a packet of charge dQ moves from INTV
CC
to
ground. The resulting dQ/dt is a current out of INTV
CC
that
is typically much larger than the control circuit current. In
continuous mode, I
GATECHG
= (Q
T
+ Q
B
), where Q
T
and Q
B
are the gate charges of the topside and bottom side
MOSFETs.
Supplying INTV
CC
power through the EXTV
CC
switch input
from an output-derived source will scale the V
IN
current
required for the driver and control circuits by the ratio
(Duty Factor)/(Efficiency). For example, in a 20V to 5V
application, 10mA of INTV
CC
current results in approxi-
mately 3mA of V
IN
current. This reduces the mid-current
loss from 10% or more (if the driver was powered directly
from V
IN
) to only a few percent.
3) I
2
R losses are predicted from the DC resistances of the
fuse (if used), MOSFET, inductor, current sense resistor,
and input and output capacitor ESR. In continuous mode
the average output current flows through L and R
SENSE
,
but is “chopped” between the topside MOSFET and the
synchronous MOSFET. If the two MOSFETs have approxi-
mately the same R
DS(ON)
, then the resistance of one
MOSFET can simply be summed with the resistances of L,
R
SENSE
and ESR to obtain I
2
R losses. For example, if each
R
DS(ON)
=10m
, R
L
=10m
, and R
SENSE
=5m
, then the
total resistance is 25m
. This results in losses ranging
from 2% to 8% as the output current increases from 3A to
15A per output stage for a 5V output, or a 3% to 12% loss
per output stage for a 3.3V output. Efficiency varies as the
inverse square of V
OUT
for the same external components
and output power level. The combined effects of increas-
ingly lower output voltages and higher currents required
by high performance digital systems is not doubling but
quadrupling the importance of loss terms in the switching
regulator system!
4) Transition losses apply only to the topside MOSFET(s),
and only when operating at high input voltages (typically
20V or greater). Transition losses can be estimated from:
Transition Loss = (1.7) V
IN2
I
O(MAX)
C
RSS
f
Other “hidden” losses such as copper trace and internal
battery resistances can account for an additional 5% to
10% efficiency degradation in portable systems. It is very
important to include these “system” level losses in the
design of a system. The internal battery and input fuse
resistance losses can be minimized by making sure that
C
IN
has adequate charge storage and a very low ESR at the
switching frequency. A 50W supply will typically require a
minimum of 200
μ
F to 300
μ
F of capacitance having a
maximum of 10m
to 20m
of ESR. The LTC1629
PolyPhase architecture typically halves to quarters this
input capacitance requirement over competing solutions.
Other losses including Schottky conduction losses during
dead-time and inductor core losses generally account for
less than 2% total additional loss.
APPLICATIU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1629-PG | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1629CG-PG | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1629 | Dual LinCMOS(TM) Timer 14-SOIC |
| LTC1629C | Dual LinCMOS(TM) Timer 14-SOIC |
| LTC1629C-PG | Dual LinCMOS(TM) Timer 14-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1642ACGN | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 16.5V 16-Pin SSOP N |
| LTC1642ACGN#PBF | 功能描述:IC CONTROLLER HOTSWAP ADJ 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC1642ACGN#TRPBF | 功能描述:IC CONTROLLER HOTSWAP ADJ 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC1642AIGN | 制造商:Linear Technology 功能描述:Hot Swap Controller 1-CH 16.5V 16-Pin SSOP N |
| LTC1642AIGN#PBF | 功能描述:IC CONTROLLER HOTSWAP ADJ 16SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。