- 您現在的位置：買賣IC網 > Datasheet目錄41 > LTC1647-1IS8#TRPBF (Linear Technology)IC CONTROLLR HOTSWAP DUAL 8-SOIC Datasheet資料下載
參數資料
| 型號： | LTC1647-1IS8#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 8/22頁 |
| 文件大?。?/td> | 239K |
| 描述： | IC CONTROLLR HOTSWAP DUAL 8-SOIC |
| 標準包裝： | 2,500 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 2.7 V ~ 16.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
LTC1647-1/
LTC1647-2/LTC1647-3
8
1647fa
PIN FUNCTIONS
V
CC1
(LTC1647-3): Channel 1 Positive Supply Input.
The supply range for normal operation is 2.7V to 16.5V .
The supply current, I
CC1
, is typically 1mA. Channel 1s
undervoltage lockout (UVLO) circuit disables GATE 1 until
the supply voltage at V
CC1
is greater than V
LKO
(typically
2.45V). GATE 1 is held at ground potential until UVLO
deactivates. If ON1 is high and V
CC1
is above the UVLO
threshold voltage, GATE 1 is pulled high by a 10糀 current
source. If V
CC1
falls below (V
LKO
V
LKH
), GATE 1 is pulled
immediately to ground. The internal reference and the
common charge pump are powered from the higher of
the two V
CC
inputs, V
CC1
or V
CC2
.
V
CC2
(LTC1647-3): Channel 2 Positive Supply Input. See
V
CC1
for functional description.
V
CC
: The Common Positive Supply Input for the LTC1647-1
and the LTC1647-2. V
CC1
and V
CC2
are internally connected
together.
GND: Chip Ground.
ON1: Channel 1 ON Input. The threshold at the ON1 pin is
set at 1.29V with 70mV hysteresis. If UVLO and the circuit
breaker of channel 1 are inactive, a logic high at ON1 enables
the 10糀 charge pump current source, pulling the GATE
1 pin above V
CC1
. If the ON1 pin is pulled low, the GATE 1
pin is pulled to ground by a 50糀 current sink.
ON1 resets channel 1s electronic circuit breaker by pulling
ON1 low for greater than one t
RESET
period (50約). A
low-to-high transition at ON1 restarts a normal GATE 1
pull-up sequence.
ON2: Channel 2 ON Input. See ON1 for functional
description.
FAULT1: Channel 1 Open-Drain Fault Status Output. FAULT1
pin pulls low after 0.3約 (t
FAULT
) if the circuit breaker
measures greater than 50mV across the sense resistor
connected between V
CC1
and SENSE 1. If FAULT1 pulls
low, GATE 1 also pulls low. FAULT1 remains low until ON1
is pulled low for at least one t
RESET
period.
FAULT2: Channel 2 Open-Drain Fault Status Output. See
FAULT 1 for functional description.
SENSE1: Channel 1 Circuit Breaker Current Sense Input.
Load current is monitored by a sense resistor connected
between V
CC1
and SENSE 1. The circuit breaker trips if the
voltage across the sense resistor exceeds 50mV (V
CB
). To
disable the circuit breaker, connect SENSE 1 to V
CC1
. In
order to obtain optimum performance, use Kelvin-sense
connections between the V
CC
and SENSE pins to the
current sense resistor.
SENSE2: Channel 2 Circuit Breaker Current Sense Input.
See SENSE 1 for functional description.
GATE1: Channel 1 N-channel MOSFET Gate Drive Output.
An internal charge pump guarantees at least 10V of gate
drive from a 5V supply. Two Zener clamps are incorporated
at the GATE 1 pin; one Zener clamps GATE 1 approximately
15V above V
CC
and the second Zener clamps GATE 1
appoximately 28V above GND. The rise time at GATE 1 is
set by an external capacitor connected between GATE 1
and GND and an internal 10糀 current source provided
by the charge pump. The fall time at GATE 1 is set by
the 50糀 current sink if ON1 is pulled low. If the circuit
breaker is tripped or the supply voltage hits the UVLO
threshold, a 50mA current sink rapidly pulls GATE 1 low.
An external 23V Zener from GATE1 to GND is required for
supply voltages (V
CC1
) greater than 10V.
GATE2: Channel 2 N-channel MOSFET Gate Drive Output.
See GATE 1 for functional description.
NC: No Connection.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1704EGN#TRPBF | IC REG DL BUCK/LINEAR 16SSOP |
| LTC1966MPMS8#TRPBF | IC RMS/DC CONV MICROPWR 8-MSOP |
| LTC1967IMS8#TRPBF | IC CONVERTER RMS-DC PREC 8MSOP |
| LTC1968IMS8#TRPBF | IC CONVERTER RMS-DC PREC 8MSOP |
| LTC3100EUD#TRPBF | IC REG BUCK/BOOST/LINEAR 16-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1647-2CS8 | 功能描述:IC CONTROLLER HOTSWAP DUAL 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC1647-2CS8#PBF | 功能描述:IC CTLR HOTSWAP DUAL 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 標準包裝:50 系列:- 類型:熱交換控制器 應用:-48V 遠程電力系統，AdvancedTCA ? 系統，高可用性 內部開關:無 電流限制:可調 電源電壓:11.5 V ~ 14.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| LTC1647-2CS8#TR | 功能描述:IC CONTROLLER HOTSWAP DUAL 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC1647-2CS8#TRPBF | 功能描述:IC CONTROLLR HOTSWAP DUAL 8-SOIC RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
| LTC1647-2IS8 | 功能描述:IC CONTROLLER HOTSWAP DUAL 8SOIC RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:100 系列:- 類型:熱插拔開關 應用:通用 內部開關:是 電流限制:可調 電源電壓:9 V ~ 13.2 V 工作溫度:-40°C ~ 150°C 安裝類型:表面貼裝 封裝/外殼:10-WFDFN 裸露焊盤 供應商設備封裝:10-TDFN-EP（3x3） 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。