- 您現在的位置：買賣IC網 > PDF目錄377763 > LTC1733 (Linear Technology Corporation) Monolithic Linear Lithium-Ion Battery Charger with Thermal Regulation PDF資料下載
參數資料
| 型號： | LTC1733 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | Monolithic Linear Lithium-Ion Battery Charger with Thermal Regulation |
| 中文描述： | 單片線性鋰離子電池充電器與熱調節 |
| 文件頁數： | 10/16頁 |
| 文件大?。?/td> | 169K |
| 代理商： | LTC1733 |
LTC1733
10
sn1733 1733fs
Open-Drain Status Outputs
The LTC1733 has three open-drain status outputs: ACPR,
CHRG and FAULT. The ACPR pin pulls low when an input
voltage greater than the undervoltage lockout threshold is
applied and goes high impedance when power (V
IN
< V
UV
)
is removed. CHRG and FAULT work together to indicate
the status of the charge cycle. Table 1 describes the status
of the charge cycle based on the CHRG and FAULT
outputs.
Table 1.
FAULT
High
CHRG
Low
Description
Charge cycle has started, C/10 has not been
reached and charging is proceeding normally.
Charge cycle has started, C/10 has not been
reached, but the charge current and timer
have been paused due to an NTC out-of-
temperature condition.
C/10 has been reached and charging is
proceeding normally.
C/10 has been reached but the charge current
and timer have paused due to an
NTC out-of-temperature condition.
Normal timeout (charging has terminated).
If FAULT goes low and CHRG goes high
impedance simultaneously, then the LTC1733
has timed out due to a bad cell (V
BAT
<2.48V
after one-quarter the programmed charge time).
If CHRG goes high impedance first, then
the LTC1733 has timed out normally (charging
has terminated), but NTC is indicating an out-
of-temperature condition.
Low
Low
High
25
μ
A
pulldown
25
μ
A
pulldown
Low
High
Low
High
High
CHRG Status Output Pin
When the charge cycle starts, the CHRG pin is pulled to
ground by an internal N-channel MOSFET capable of
driving an LED. When the charge current drops to 10% of
the full-scale current (C/10), the N-channel MOSFET is
latched off and a weak 25
μ
A current source to ground is
connected to the CHRG pin. After a time-out occurs, the
pin assumes a high impedance state. By using two differ-
ent value pull-up resistors a microprocessor can detect
three states from this pin (charging, C/10, and time-out).
See Figure 2.
APPLICATIOU
W
U
U
When the LTC1733 is in charge mode, the CHRG pin is
pulled low by the internal N-channel MOSFET. To detect
this mode, force the digital output pin, OUT, high and
measure the voltage at the CHRG pin. The N-channel
MOSFET will pull the pin low even with the 2k pull-up
resistor. Once the charge current drops to 10% of the full-
scale current (C/10), the N-channel MOSFET is turned off
and a 25
μ
A current source is connected to the CHRG pin.
The IN pin will then be pulled high by the 2k pull-up. By
forcing the OUT pin to a high impedance state, the current
source will pull the pin low through the 400k resistor.
When the internal timer has expired, the CHRG pin will
assume a high impedance state and the 400k resistor will
then pull the pin high to indicate that charging has termi-
nated.
NTC Thermistor
The battery temperature is measured by placing a negative
temperature coefficient (NTC) thermistor close to the
battery pack. The NTC circuitry is shown in Figure 3. To use
this feature, connect a 10k NTC thermistor between the
NTC pin and ground and a resistor (R
HOT
) from the NTC pin
to V
CC
. R
HOT
should be a 1% resistor with a value equal to
the value of the chosen NTC thermistor at 50
°
C (this value
is 4.1k for a Vishay NTHS0603N02N1002J thermistor).
The LTC1733 goes into hold mode when the resistance of
the NTC thermistor drops below 4.1k which should be
at 50
°
C. The hold mode freezes the timer and stops
the charge cycle until the thermistor indicates a return
to a valid temperature. As the temperature drops, the
Figure 2. Microprocessor Interface
8
3
400k
2k
LTC1733
1733 F02
V
CC
CHRG
V
+
μ
PROCESSOR
V
DD
OUT
IN
相關PDF資料 |
PDF描述 |
|---|---|
| LTC1733EMSE | Monolithic Linear Lithium-Ion Battery Charger with Thermal Regulation |
| LTC1734 | Lithium-Ion Linear Battery Charger in SOT-23(鋰離子線性電池充電器（SOT-23封裝）) |
| LTC1735IS | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1735C-1 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
| LTC1735CS-1 | RADIATION HARDENED HIGH EFFICIENCY, 5 AMP SWITCHING REGULATORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1733EMSE | 功能描述:IC CHRGR BATT MONO THERML 10MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC1733EMSE#PBF | 功能描述:IC CHRGR BATT MONO THERML 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 其它有關文件:STC3100 View All Specifications 特色產品:STC3100 - Battery Monitor IC 標準包裝:4,000 系列:- 功能:燃料，電量檢測計/監控器 電池化學:鋰離子（Li-Ion） 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-MiniSO 包裝:帶卷 (TR) 其它名稱:497-10526-2 |
| LTC1733EMSE#PBF | 制造商:Linear Technology 功能描述:Battery Management IC |
| LTC1733EMSE#TR | 功能描述:IC CTRLR BATT CHRG LI-ION 10MSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
| LTC1733EMSE#TRPBF | 功能描述:IC CHRGR BATT MONO THERML 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 電池管理 系列:- 標準包裝:61 系列:- 功能:電源管理 電池化學:鋰離子（Li-Ion）、鋰聚合物（Li-Pol） 電源電壓:4.35 V ~ 5.5 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:22-WFDFN 裸露焊盤 供應商設備封裝:22-DFN（6x3）裸露焊盤 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。