- 您現在的位置：買賣IC網 > PDF目錄3303 > LTC1992HMS8 (Linear Technology)IC AMP DIFF I/O ADJ OUT 8-MSOP PDF資料下載
參數資料
| 型號： | LTC1992HMS8 |
| 廠商： | Linear Technology |
| 文件頁數： | 24/42頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP DIFF I/O ADJ OUT 8-MSOP |
| 標準包裝： | 50 |
| 放大器類型： | 差分 |
| 電路數： | 1 |
| 輸出類型： | 差分，滿擺幅 |
| 轉換速率： | 1.5 V/µs |
| 增益帶寬積： | 3.2MHz |
| 電流 - 輸入偏壓： | 2pA |
| 電壓 - 輸入偏移： | 250µV |
| 電流 - 電源： | 700µA |
| 電流 - 輸出 / 通道： | 30mA |
| 電壓 - 電源，單路/雙路(±)： | 2.7 V ~ 11 V，±1.35 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁當前第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
LTC1992 Family
30
1992fb
APPLICATIONS INFORMATION
The VOCM input pin has a very high input impedance and
is easily driven by even the weakest of sources. Many
ADCs provide a voltage reference output that defines
either its common mode level or its full-scale level. Apply
the ADC’s reference potential either directly to the VOCM
pin or through a resistive voltage divider depending on
the reference voltage’s definition. When controlling the
VOCM pin by a high impedance source, connect a bypass
capacitor (1000pF to 0.1μF) from the VOCM pin to ground
to lower the high frequency impedance and limit external
noise coupling. Other applications will want the output
biased at a midpoint of the power supplies for maximum
output voltage swing. For these applications, the LTC1992
provides a mid-supply potential at the VMID pin. The VMID
pin connects to a simple resistive voltage divider with
two 200k resistors connected between the supply pins.
To use this feature, connect the VMID pin to the VOCM pin
and bypass this node with a capacitor.
One undesired effect of utilizing the level shifting function
is an increase in the differential output offset voltage due to
gain setting resistor mismatch. The offset is approximately
the amount of level shift (VOUTCM – VINCM) multiplied by the
amount of resistor mismatch. For example, a 2V level shift
with 0.1% resistors will give around 2mV of output offset
(2 0.1% = 2mV). The exact amount of offset is dependent
on the application’s gain and the resistor mismatch. For a
detail description, consult the Fully Differential Amplifier
Applications Circuit Analysis section.
CMRR and Output Balance
One common misconception of fully differential amplifiers
is that the common mode level servo guarantees an infinite
common mode rejection ratio (CMRR). This is not true. The
common mode level servo does, however, force the two
outputs to be truly complementary (i.e., exactly opposite
or 180 degrees out of phase). Output balance is a measure
of how complementary the two outputs are.
At low frequencies, CMRR is primarily determined by the
matching of the gain setting resistors. Like any op amp, the
LTC1992 does not have infinite CMRR, however resistor
mismatching of only 0.018%, halves the circuit’s CMRR.
Standard 1% tolerance resistors yield a CMRR of about
40dB. For most applications, resistor matching dominates
low frequency CMRR performance. The specifications for
the fixed gain LTC1992-X parts include the on-chip resistor
matching effects. Also, note that an input common mode
signal appears as a differential output signal reduced by the
CMRR. As with op amps, at higher frequencies the CMRR
degrades. Refer to the Typical Performance plots for the
details of the CMRR performance over frequency.
At low frequencies, the output balance specification is
determined by the matching of the on-chip RCMM and
RCMP resistors. At higher frequencies, the output bal-
ance degrades. Refer to the typical performance plots
for the details of the output balance performance over
frequency.
Input Impedance
The input impedance for a fully differential amplifier ap-
plication circuit is similar to that of a standard op amp
inverting amplifier. One major difference is that the input
impedance is different for differential input signals and
single-ended signals. Referring to Figure 3, for differential
input signals the input impedance is expressed by the
following expression:
RINDIFF = 2 RIN
For single-ended signals, the input impedance is expressed
by the following expression:
RINS-E =
RIN
1–
RFB
2 RIN + RFB
()
The input impedance for single-ended signals is slightly
higher than the RIN value since some of the input signal
is fed back and appears as the amplifier’s input common
mode level. This small amount of positive feedback in-
creases the input impedance.
Driving Capacitive Loads
The LTC1992 family of parts is stable for all capacitive loads
up to at least 10,000pF. While stability is guaranteed, the
part’s performance is not unaffected by capacitive load-
ing. Large capacitive loads increase output step response
ringing and settling time, decrease the bandwidth and
increase the frequency response peaking. Refer to the
相關PDF資料 |
PDF描述 |
|---|---|
| AS168X-CB1DF040 | CIRCUIT BRKR THERMAL 4.0A 1POLE |
| NE5532AD8R2 | IC OPAMP DUAL LOW NOISE 8-SOIC |
| NE5532AD8 | IC OPAMP DUAL LOW NOISE 8-SOIC |
| AS168X-CB1DF005 | CIRCUIT BRKR THERMAL 0.5A 1POLE |
| LTC1992IMS8 | IC AMP DIFF I/O ADJ OUT 8-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC1992HMS8#PBF | 功能描述:IC AMP/DVR I/O FULLY DIFF 8-MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 產品培訓模塊:Differential Circuit Design Techniques for Communication Applications 標準包裝:1 系列:- 放大器類型:RF/IF 差分 電路數:1 輸出類型:差分 轉換速率:9800 V/µs 增益帶寬積:- -3db帶寬:2.9GHz 電流 - 輸入偏壓:3µA 電壓 - 輸入偏移:- 電流 - 電源:40mA 電流 - 輸出 / 通道:- 電壓 - 電源，單路/雙路(±):3 V ~ 3.6 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:16-VQFN 裸露焊盤，CSP 供應商設備封裝:16-LFCSP-VQ 包裝:剪切帶 (CT) 產品目錄頁面:551 (CN2011-ZH PDF) 其它名稱:ADL5561ACPZ-R7CT |
| LTC1992HMS8#TR | 功能描述:IC AMP DIFF I/O ADJ OUT 8-MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
| LTC1992HMS8#TRPBF | 功能描述:IC AMP/DVR I/O FULLY DIFF 8-MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
| LTC1992IMS8 | 功能描述:IC AMP DIFF I/O ADJ OUT 8-MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
| LTC1992IMS8#PBF | 功能描述:IC AMP/DVR I/O FULLY DIFF 8-MSOP RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1 系列:- 放大器類型:通用 電路數:4 輸出類型:滿擺幅 轉換速率:0.6 V/µs 增益帶寬積:1MHz -3db帶寬:- 電流 - 輸入偏壓:2pA 電壓 - 輸入偏移:1000µV 電流 - 電源:85µA 電流 - 輸出 / 通道:20mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 6 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOICN 包裝:剪切帶 (CT) 產品目錄頁面:680 (CN2011-ZH PDF) 其它名稱:MCP6L04T-E/SLCT |
發布緊急采購，3分鐘左右您將得到回復。