- 您現在的位置：買賣IC網 > PDF目錄2005 > LTC2222IUK-11#TRPBF (Linear Technology)IC ADC 11BIT 105MSPS SAMPL 48QFN PDF資料下載
參數資料
| 型號： | LTC2222IUK-11#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 11/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 11BIT 105MSPS SAMPL 48QFN |
| 標準包裝： | 2,000 |
| 位數： | 11 |
| 采樣率（每秒）： | 105M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 535mW |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 48-QFN-EP（7x7） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，雙極; 1 個差分，雙極 |
LTC2222-11
19
222211f
APPLICATIO S I FOR ATIO
WU
UU
to the same power supply as for the logic being driven. For
example if the converter is driving a DSP powered by a 1.8V
supply then OVDD should be tied to that same 1.8V supply.
OVDD can be powered with any voltage up to 3.6V. OGND
can be powered with any voltage from GND up to 1V and
must be less than OVDD. The logic outputs will swing be-
tween OGND and OVDD.
Output Enable
The outputs may be disabled with the output enable pin, OE.
OE high disables all data outputs including OF and
CLOCKOUT. The data access and bus relinquish times are
too slow to allow the outputs to be enabled and disabled
during full speed operation. The output Hi-Z state is intended
for use during long periods of inactivity.
Sleep and Nap Modes
The converter may be placed in shutdown or nap modes
to conserve power. Connecting SHDN to GND results in
normal operation. Connecting SHDN to VDD and OE to VDD
results in sleep mode, which powers down all circuitry
including the reference and typically dissipates 1mW. When
exiting sleep mode it will take milliseconds for the output
data to become valid because the reference capacitors have
to recharge and stabilize. Connecting SHDN to VDD and OE
to GND results in nap mode, which typically dissipates
35mW. In nap mode, the on-chip reference circuit is kept
on, so that recovery from nap mode is faster than that from
sleep mode, typically taking 100 clock cycles. In both sleep
and nap mode all digital outputs are disabled and enter the
Hi-Z state.
GROUNDING AND BYPASSING
The LTC2222-11 requires a printed circuit board with a clean
unbroken ground plane. A multilayer board with an inter-
nal ground plane is recommended. Layout for the printed
circuit board should ensure that digital and analog signal
lines are separated as much as possible. In particular, care
should be taken not to run any digital signal alongside an
analog signal or underneath the ADC.
High quality ceramic bypass capacitors should be used at
the VDD,OVDD,VCM,REFHA,REFHB,REFLAandREFLBpins
as shown on the schematic on Page 20 of this data sheet.
Bypass capacitors must be located as close to the pins as
possible. Of particular importance are the capacitors be-
tween REFHA and REFLB and between REFHB and REFLA.
These capacitors should be as close to the device as pos-
sible (1.5mm or less). Size 0402 ceramic capacitors are
recommended. The 2.2
F capacitor between REFHA and
REFLA can be somewhat further away. The traces connect-
ing the pins and bypass capacitors must be kept short and
should be made as wide as possible.
The LTC2222-11 differential inputs should run parallel and
close to each other. The input traces should be as short as
possible to minimize capacitance and to minimize noise
pickup.
HEAT TRANSFER
Most of the heat generated by the LTC2222-11 is transferred
from the die through the bottom-side exposed pad and
package leads onto the printed circuit board. For good
electrical and thermal performance, the exposed pad should
be soldered to a large grounded pad on the PC board. It is
critical that all ground pins are connected to a ground plane
of sufficient area.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2223IUK#TRPBF | IC ADC 12BIT 80MSPS SAMPLE 48QFN |
| LTC2224IUK#TRPBF | IC ADC 12BIT 135MSPS SAMPL 48QFN |
| LTC2225IUH#TRPBF | IC ADC 12BIT 10MSPS 3V 32-QFN |
| LTC2228IUH#TRPBF | IC ADC 12BIT 65MSPS SAMPL 32-QFN |
| LTC2229IUH#PBF | IC ADC 12-BIT 80MSPS 3V 32-QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2222UK | 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit,105Msps/80Msps ADCs |
| LTC2222UK-11 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:11-Bit, 105Msps ADC |
| LTC2223 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit,105Msps/80Msps ADCs |
| LTC2223CUK | 功能描述:IC ADC 12BIT 80MSPS SAMPLE 48QFN RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC2223CUK#PBF | 功能描述:IC ADC 12BIT 80MSPS SAMPLE 48QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
發布緊急采購，3分鐘左右您將得到回復。