- 您現在的位置：買賣IC網 > PDF目錄10516 > LTC2224CUK#PBF (Linear Technology)IC ADC 12BIT 135MSPS SAMPL 48QFN PDF資料下載
參數資料
| 型號： | LTC2224CUK#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 6/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 12BIT 135MSPS SAMPL 48QFN |
| 標準包裝： | 52 |
| 位數： | 12 |
| 采樣率（每秒）： | 135M |
| 數據接口： | 并聯 |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 680mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 48-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 48-QFN-EP（7x7） |
| 包裝： | 管件 |
| 輸入數目和類型： | 1 個單端，雙極; 1 個差分，雙極 |
LTC2224
14
2224fa
During the sample phase when ENC is low, the transistors
connect the analog inputs to the sampling capacitors and
they charge to, and track the differential input voltage.
When ENC transitions from low to high, the sampled input
voltage is held on the sampling capacitors. During the hold
phase when ENC is high, the sampling capacitors are
disconnected from the input and the held voltage is passed
to the ADC core for processing. As ENC transitions from
high to low, the inputs are reconnected to the sampling
capacitors to acquire a new sample. Since the sampling
capacitors still hold the previous sample, a charging glitch
proportional to the change in voltage between samples will
be seen at this time. If the change between the last sample
and the new sample is small, the charging glitch seen at
the input will be small. If the input change is large, such as
the change seen with input frequencies near Nyquist, then
a larger charging glitch will be seen.
Single-Ended Input
For cost sensitive applications, the analog inputs can be
driven single-ended. With a single-ended input the har-
monic distortion and INL will degrade, but the SNR and
DNL will remain unchanged. For a single-ended input, AIN+
should be driven with the input signal and AIN– should be
connected to 1.6V or VCM.
Common Mode Bias
For optimal performance the analog inputs should be
driven differentially. Each input should swing
±0.5V for
the 2V range or
±0.25V for the 1V range, around a
common mode voltage of 1.6V. The VCM output pin (Pin
44) may be used to provide the common mode bias level.
VCM can be tied directly to the center tap of a transformer
to set the DC input level or as a reference level to an op amp
differential driver circuit. The VCM pin must be bypassed to
ground close to the ADC with a 2.2
F or greater capacitor.
Input Drive Impedance
As with all high performance, high speed ADCs, the
dynamic performance of the LTC2224 can be influenced
by the input drive circuitry, particularly the second and
third harmonics. Source impedance and input reactance
can influence SFDR. At the falling edge of ENC, the sample-
and-hold circuit will connect the 1.6pF sampling capacitor
to the input pin and start the sampling period. The sam-
pling period ends when ENC rises, holding the sampled
input on the sampling capacitor. Ideally the input circuitry
should
be
fast
enough
to
fully
charge
the sampling capacitor during the sampling period
1/(2FENCODE); however, this is not always possible and the
incomplete settling may degrade the SFDR. The sampling
glitch has been designed to be as linear as possible to
minimize the effects of incomplete settling.
For the best performance, it is recommended to have a
source impedance of 100
or less for each input. The
source impedance should be matched for the differential
inputs. Poor matching will result in higher even order
harmonics, especially the second.
Input Drive Circuits
Figure 3 shows the LTC2224 being driven by an RF
transformer with a center tapped secondary. The second-
ary center tap is DC biased with VCM, setting the ADC input
25
25
25
25
0.1
F
AIN
+
AIN
–
12pF
2.2
F
VCM
LTC2224
ANALOG
INPUT
0.1
FT1
1:1
T1 = MA/COM ETC1-1T
RESISTORS, CAPACITORS
ARE 0402 PACKAGE SIZE
2224 F03
Figure 3. Single-Ended to Differential Conversion
Using a Transformer
APPLICATIO S I FOR ATIO
WU
UU
相關PDF資料 |
PDF描述 |
|---|---|
| UP050B821K-NAC | CAP CER 820PF 50V 10% AXIAL |
| VE-B4D-MX-F1 | CONVERTER MOD DC/DC 85V 75W |
| VE-B4B-MX-F4 | CONVERTER MOD DC/DC 95V 75W |
| AD9286BCPZ-500 | IC ADC 8BIT SPI/SRL 500M 48LFSCP |
| UP050B821K-KFC | CAP CER 820PF 50V 10% AXIAL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2224IUK | 功能描述:IC ADC 12BIT 135MSPS SAMPL 48QFN RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2224IUK#PBF | 功能描述:IC ADC 12BIT 135MSPS SAMPL 48QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2224IUK#TR | 功能描述:IC ADC 12BIT 135MSPS SAMPL 48QFN RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2224IUK#TRPBF | 功能描述:IC ADC 12BIT 135MSPS SAMPL 48QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2224UK | 制造商:LINER 制造商全稱:Linear Technology 功能描述:12-Bit, 135Msps ADC |
發布緊急采購，3分鐘左右您將得到回復。