參數資料
型號： LTC2258CUJ-12#TRPBF
廠商： Linear Technology
文件頁數： 7/34頁
文件大?。?/td> 0K
描述： IC ADC 12BIT 65MSPS 1.8V 40-QFN
產品培訓模塊： LTC2262 - Ultra Low Power High Speed ADCs
標準包裝： 2,000
位數： 12
采樣率（每秒）： 65M
數據接口： 并聯，串行，SPI
轉換器數目： 1
功率耗散（最大）： 89mW
電壓電源： 單電源
工作溫度： 0°C ~ 70°C
安裝類型： 表面貼裝
封裝/外殼： 40-WFQFN 裸露焊盤
供應商設備封裝： 40-QFN（6x6）
包裝： 帶卷 (TR)
輸入數目和類型： 1 個差分
配用： DC718C-ND - DEMO QUIKEVAL-II DATA
LTC2258-12
LTC2257-12/LTC2256-12
15
225812fd
For more information www.linear.com/LTC2258-12
pin FuncTions
PINS THAT ARE THE SAME FOR ALL DIGITAL OUTPUT
MODES
AIN+ (Pin 1): Positive Differential Analog Input.
AIN– (Pin 2): Negative Differential Analog Input.
GND (Pin 3): ADC Power Ground.
REFH (Pins 4, 5): ADC High Reference. Bypass to Pins
6, 7 with a 2.2F ceramic capacitor and to ground with a
0.1F ceramic capacitor.
REFL (Pins 6, 7): ADC Low Reference. Bypass to Pins
4, 5 with a 2.2F ceramic capacitor and to ground with a
0.1F ceramic capacitor.
PAR/SER (Pin 8): Programming Mode Selection Pin. Con-
nect to ground to enable the serial programming mode.
CS, SCK, SDI, SDO become a serial interface that control
the A/D operating modes. Connect to VDD to enable the
parallel programming mode where CS, SCK, SDI become
parallel logic inputs that control a reduced set of the A/D
operating modes. PAR/SER should be connected directly
to ground or the VDD of the part and not be driven by a
logic signal.
VDD (Pins 9, 10, 40): 1.8V Analog Power Supply. Bypass
to ground with 0.1F ceramic capacitors. Pins 9 and 10
can share a bypass capacitor.
ENC+ (Pin 11): Encode Input. Conversion starts on the
rising edge.
ENC– (Pin 12): Encode Complement Input. Conversion
starts on the falling edge.
CS (Pin 13): In serial programming mode, (PAR/SER =
0V), CS is the serial interface chip select input. When
CS is low, SCK is enabled for shifting data on SDI into
the mode control registers. In the parallel programming
mode (PAR/SER = VDD), CS controls the clock duty cycle
stabilizer. When CS is low, the clock duty cycle stabilizer is
turned off. When CS is high, the clock duty cycle stabilizer
is turned on. CS can be driven with 1.8V to 3.3V logic.
SCK (Pin 14): In serial programming mode, (PAR/SER
= 0V), SCK is the serial interface clock input. In the
parallel programming mode (PAR/SER = VDD), SCK
controls the digital output mode. When SCK is low,
the full-rate CMOS output mode is enabled. When SCK
is high, the double data rate LVDS output mode (with
3.5mA output current) is enabled. SCK can be driven
with 1.8V to 3.3V logic.
SDI (Pin 15): In serial programming mode, (PAR/SER =
0V), SDI is the serial interface data input. Data on SDI is
clocked into the mode control registers on the rising edge
of SCK. In the parallel programming mode (PAR/SER =
VDD), SDI can be used to power down the part. When SDI
is low, the part operates normally. When SDI is high, the
part enters sleep mode. SDI can be driven with 1.8V to
3.3V logic.
SDO (Pin 16): In serial programming mode, (PAR/SER
= 0V), SDO is the optional serial interface data output.
Data on SDO is read back from the mode control registers
and can be latched on the falling edge of SCK. SDO is an
open-drain NMOS output that requires an external 2k
pull-up resistor to 1.8V-3.3V. If read back from the mode
control registers is not needed, the pull-up resistor is not
necessary and SDO can be left unconnected. In the parallel
programming mode (PAR/SER = VDD), SDO is not used
and should not be connected.
OGND (Pin 25): Output Driver Ground.
OVDD (Pin 26): Output Driver Supply. Bypass to ground
with a 0.1F ceramic capacitor.
VCM (Pin 37): Common Mode Bias Output, Nominally
Equal to VDD/2. VCM should be used to bias the common
mode of the analog inputs. Bypass to ground with a 0.1F
ceramic capacitor.
VREF(Pin38):ReferenceVoltageOutput,Nominally1.25V.
Bypass to ground with a 1F ceramic capacitor.
SENSE(Pin39):ReferenceProgrammingPin.Connecting
SENSEtoVDDselectstheinternalreferenceanda±1Vinput
range. Connecting SENSE to ground selects the internal
reference and a ±0.5V input range. An external reference
between 0.625V and 1.3V applied to SENSE selects an
input range of ±0.8 VSENSE.
相關PDF資料
PDF描述
VI-B6B-IV-S CONVERTER MOD DC/DC 95V 150W
VE-B3M-MW-F1 CONVERTER MOD DC/DC 10V 100W
MS27473T22B32S CONN PLUG 32POS STRAIGHT W/SCKT
13282-18SG-321 CONN PLUG 18POS CABLE SKT
LTC1485CN8 IC TXRX DIFFERNTIAL BUS 8-DIP
相關代理商/技術參數
參數描述
LTC2258CUJ-14#PBF 功能描述:IC ADC 14BIT 65MSPS 1.8V 40-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6
LTC2258CUJ-14#TRPBF 功能描述:IC ADC 14BIT 65MSPS 1.8V 40-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
LTC2258CUJ-14-PBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 65/40/25Msps Ultralow Power 1.8V ADCs
LTC2258CUJ-14-TRPBF 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 65/40/25Msps Ultralow Power 1.8V ADCs
LTC2258IUJ-12#PBF 功能描述:IC ADC 12BIT 65MSPS 1.8V 40-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*