- 您現在的位置：買賣IC網 > PDF目錄10529 > LTC2293CUP#PBF (Linear Technology)IC ADC DUAL 12BIT 65MSPS 64QFN PDF資料下載
參數資料
| 型號： | LTC2293CUP#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 9/28頁 |
| 文件大小： | 0K |
| 描述： | IC ADC DUAL 12BIT 65MSPS 64QFN |
| 標準包裝： | 40 |
| 位數： | 12 |
| 采樣率（每秒）： | 65M |
| 數據接口： | 并聯 |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 450mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 64-QFN（9x9） |
| 包裝： | 管件 |
| 輸入數目和類型： | 2 個單端，雙極; 2 個差分, 雙極 |
| 產品目錄頁面： | 1349 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
LTC2293/LTC2292/LTC2291
17
229321fa
capacitors to acquire a new sample. Since the sampling
capacitors still hold the previous sample, a charging glitch
proportional to the change in voltage between samples will
be seen at this time. If the change between the last sample
and the new sample is small, the charging glitch seen at
the input will be small. If the input change is large, such as
the change seen with input frequencies near Nyquist, then
a larger charging glitch will be seen.
Single-Ended Input
For cost sensitive applications, the analog inputs can be
driven single-ended. With a single-ended input the har-
monic distortion and INL will degrade, but the SNR and
DNL will remain unchanged. For a single-ended input, AIN+
should be driven with the input signal and AIN– should be
connected to 1.5V or VCM.
Common Mode Bias
For optimal performance the analog inputs should be
driven differentially. Each input should swing
±0.5V for
the 2V range or
±0.25V for the 1V range, around a
common mode voltage of 1.5V. The VCM output pin may
be used to provide the common mode bias level. VCM can
be tied directly to the center tap of a transformer to set the
DC input level or as a reference level to an op amp
differential driver circuit. The VCM pin must be bypassed to
ground close to the ADC with a 2.2
F or greater capacitor.
Input Drive Impedance
As with all high performance, high speed ADCs, the
dynamic performance of the LTC2293/LTC2292/LTC2291
can be influenced by the input drive circuitry, particularly
the second and third harmonics. Source impedance and
reactance can influence SFDR. At the falling edge of CLK,
the sample-and-hold circuit will connect the 4pF sampling
capacitor to the input pin and start the sampling period.
The sampling period ends when CLK rises, holding the
sampled input on the sampling capacitor. Ideally the input
circuitry should be fast enough to fully charge
the sampling capacitor during the sampling period
1/(2FENCODE); however, this is not always possible and the
incomplete settling may degrade the SFDR. The sampling
APPLICATIO S I FOR ATIO
WU
UU
glitch has been designed to be as linear as possible to
minimize the effects of incomplete settling.
For the best performance, it is recommended to have a
source impedance of 100
or less for each input. The
source impedance should be matched for the differential
inputs. Poor matching will result in higher even order
harmonics, especially the second.
Input Drive Circuits
Figure 3 shows the LTC2293/LTC2292/LTC2291 being
driven by an RF transformer with a center tapped second-
ary. The secondary center tap is DC biased with VCM,
setting the ADC input signal at its optimum DC level.
Terminating on the transformer secondary is desirable, as
this provides a common mode path for charging glitches
caused by the sample and hold. Figure 3 shows a 1:1 turns
ratio transformer. Other turns ratios can be used if the
source impedance seen by the ADC does not exceed 100
for each ADC input. A disadvantage of using a transformer
is the loss of low frequency response. Most small RF
transformers have poor performance at frequencies be-
low 1MHz.
Figure 3. Single-Ended to Differential Conversion
Using a Transformer
25
25
25
25
0.1
F
AIN
+
AIN
–
12pF
2.2
F
VCM
LTC2293
LTC2292
LTC2291
ANALOG
INPUT
0.1
FT1
1:1
T1 = MA/COM ETC1-1T
RESISTORS, CAPACITORS
ARE 0402 PACKAGE SIZE
229321 F03
Figure 4 demonstrates the use of a differential amplifier to
convert a single ended input signal into a differential input
signal. The advantage of this method is that it provides low
frequency input response; however, the limited gain band-
width of most op amps will limit the SFDR at high input
frequencies.
相關PDF資料 |
PDF描述 |
|---|---|
| ICL3225ECAZ | IC 2DRVR/2RCVR RS232 3V 20-SSOP |
| VI-J44-MW-F1 | CONVERTER MOD DC/DC 48V 100W |
| AD9219ABCPZ-65 | IC ADC 10BIT SRL 65MSPS 64LFCSP |
| VE-JNB-MY-F4 | CONVERTER MOD DC/DC 95V 50W |
| AD7762BSVZ | IC ADC 24BIT 625KSPS 64TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2293IUP | 制造商:Linear Technology 功能描述:MS-ADC/High Speed, Dual 12-bit, 65Msps Low Power ADC |
| LTC2293IUP#PBF | 功能描述:IC ADC DUAL 12BIT 65MSPS 64QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2293IUP#TRPBF | 功能描述:IC ADC DUAL 12BIT 65MSPS 64QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2293UP | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 12-Bit, 65/40/25Msps Low Power 3V ADCs |
| LTC2294 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:14-Bit, 125/105Msps Low Power 3V ADCs |
發布緊急采購，3分鐘左右您將得到回復。