- 您現在的位置：買賣IC網 > PDF目錄10109 > LTC2294CUP#TRPBF (Linear Technology)IC ADC DUAL 12BIT 80MSPS 64QFN PDF資料下載
參數資料
| 型號： | LTC2294CUP#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 5/24頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC DUAL 12BIT 80MSPS 64QFN |
| 標準包裝： | 2,000 |
| 位數： | 12 |
| 采樣率（每秒）： | 80M |
| 數據接口： | 并聯 |
| 轉換器數目： | 2 |
| 功率耗散（最大）： | 495mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 64-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 64-QFN（9x9） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 2 個單端，雙極; 2 個差分, 雙極 |
LTC2294
13
2294fa
capacitors to acquire a new sample. Since the sampling
capacitors still hold the previous sample, a charging glitch
proportional to the change in voltage between samples will
be seen at this time. If the change between the last sample
and the new sample is small, the charging glitch seen at
the input will be small. If the input change is large, such as
the change seen with input frequencies near Nyquist, then
a larger charging glitch will be seen.
Single-Ended Input
For cost sensitive applications, the analog inputs can be
driven single-ended. With a single-ended input the har-
monic distortion and INL will degrade, but the SNR and
DNL will remain unchanged. For a single-ended input, AIN+
should be driven with the input signal and AIN– should be
connected to 1.5V or VCM.
Common Mode Bias
For optimal performance the analog inputs should be
driven differentially. Each input should swing
±0.5V for
the 2V range or
±0.25V for the 1V range, around a
common mode voltage of 1.5V. The VCM output pin may
be used to provide the common mode bias level. VCM can
be tied directly to the center tap of a transformer to set the
DC input level or as a reference level to an op amp
differential driver circuit. The VCM pin must be bypassed to
ground close to the ADC with a 2.2
F or greater capacitor.
Input Drive Impedance
As with all high performance, high speed ADCs, the
dynamic performance of the LTC2294 can be influenced
by the input drive circuitry, particularly the second and
third harmonics. Source impedance and reactance can
influence SFDR. At the falling edge of CLK, the sample-
and-hold circuit will connect the 4pF sampling capacitor to
the input pin and start the sampling period. The sampling
period ends when CLK rises, holding the sampled input on
the sampling capacitor. Ideally the input circuitry should
be fast enough to fully charge the sampling capacitor
during the sampling period 1/(2FENCODE); however, this is
not always possible and the incomplete settling may
degrade the SFDR. The sampling glitch has been designed
APPLICATIO S I FOR ATIO
WU
UU
to be as linear as possible to minimize the effects of
incomplete settling.
For the best performance, it is recommended to have a
source impedance of 100
or less for each input. The
source impedance should be matched for the differential
inputs. Poor matching will result in higher even order
harmonics, especially the second.
Input Drive Circuits
Figure 3 shows the LTC2294 being driven by an RF
transformer with a center tapped secondary. The second-
ary center tap is DC biased with VCM, setting the ADC input
signal at its optimum DC level. Terminating on the trans-
former secondary is desirable, as this provides a common
mode path for charging glitches caused by the sample and
hold. Figure 3 shows a 1:1 turns ratio transformer. Other
turns ratios can be used if the source impedance seen by
the ADC does not exceed 100
for each ADC input. A
disadvantage of using a transformer is the loss of low
frequency response. Most small RF transformers have
poor performance at frequencies below 1MHz.
Figure 3. Single-Ended to Differential Conversion
Using a Transformer
25
25
25
25
0.1
F
AIN
+
AIN
–
12pF
2.2
F
VCM
LTC2294
ANALOG
INPUT
0.1
FT1
1:1
T1 = MA/COM ETC1-1T
RESISTORS, CAPACITORS
ARE 0402 PACKAGE SIZE
2294 F03
Figure 4 demonstrates the use of a differential amplifier to
convert a single ended input signal into a differential input
signal. The advantage of this method is that it provides low
frequency input response; however, the limited gain band-
width of most op amps will limit the SFDR at high input
frequencies.
相關PDF資料 |
PDF描述 |
|---|---|
| VE-B3F-IV-F2 | CONVERTER MOD DC/DC 72V 150W |
| LTC1383CS#TRPBF | IC TXRX 5V RS232 LOW PWR 16-SOIC |
| IDT72201L25PFI | IC FIFO 256X9 SYNC 25NS 32-TQFP |
| MS3102R20-14S | CONN RCPT 5POS BOX MNT W/SCKT |
| VE-B3F-IV-F1 | CONVERTER MOD DC/DC 72V 150W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2294IUP | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 12-Bit, 80Msps Low Power 3V ADC |
| LTC2294IUP#PBF | 功能描述:IC ADC DUAL 12BIT 80MSPS 64QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| LTC2294IUP#TRPBF | 功能描述:IC ADC DUAL 12BIT 80MSPS 64QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2294UP | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 12-Bit, 80Msps Low Power 3V ADC |
| LTC2295 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Dual 14-Bit, 10Msps Low Power 3V ADC |
發布緊急采購，3分鐘左右您將得到回復。