- 您現在的位置：買賣IC網 > PDF目錄10136 > LTC2364HMS-18#TRPBF (Linear Technology)IC ADC 18BIT 250K 1CH 16MSOP PDF資料下載
參數資料
| 型號： | LTC2364HMS-18#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 3/24頁 |
| 文件大小： | 0K |
| 描述： | IC ADC 18BIT 250K 1CH 16MSOP |
| 產品培訓模塊： | LTC2369- 18-/16-bit Pseudo-Differential SAR ADC Family Overview |
| 標準包裝： | 2,500 |
| 位數： | 18 |
| 采樣率（每秒）： | 250k |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 4.25mW |
| 電壓電源： | 模擬和數字 |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-TFSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 16-MSOP |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個偽差分，單極 |
| 配用： | DC1813A-H-ND - BOARD SAR ADC LTC2364-18 |
LTC2364-18
11
236418f
APPLICATIONS INFORMATION
INPUT DRIVE CIRCUITS
A low impedance source can directly drive the high im-
pedance input of the LTC2364-18 without gain error. A
high impedance source should be buffered to minimize
settling time during acquisition and to optimize the dis-
tortion performance of the ADC. Minimizing settling time
is important even for DC inputs, because the ADC input
draws a current spike when entering acquisition.
For best performance, a buffer amplifier should be used
to drive the analog input of the LTC2364-18. The ampli-
fier provides low output impedance, which produces fast
settling of the analog signal during the acquisition phase.
It also provides isolation between the signal source and
the current spike the ADC input draws.
Input Filtering
The noise and distortion of the buffer amplifier and signal
sourcemustbeconsideredsincetheyaddtotheADCnoise
and distortion. Noisy input signals should be filtered prior
to the buffer amplifier input with an appropriate filter to
minimizenoise.Thesimple1-poleRClowpassfilter(LPF1)
shown in Figure 4 is sufficient for many applications.
High quality capacitors and resistors should be used in the
RCfilterssincethesecomponentscanadddistortion.NPO
and silver mica type dielectric capacitors have excellent
linearity. Carbon surface mount resistors can generate
distortion from self heating and from damage that may
occurduringsoldering.Metalfilmsurfacemountresistors
are much less susceptible to both problems.
Pseudo-Differential Unipolar Inputs
For most applications, we recommend the low power
LT6202 ADC driver to drive the LTC2364-18. With a low
noise density of 1.9nV/√Hz and a low supply current of
3mA, the LT6202 is flexible and may be configured to
convert signals of various amplitudes to the 0V to 5V input
range of the LTC2364-18.
To achieve the full distortion performance of the
LTC2364-18, a low distortion single-ended signal source
driven through the LT6202 configured as a unity-gain buf-
fer as shown in Figure 4 can be used to get the full data
sheet THD specification of –120dB.
The LT6202 can also be used to buffer and convert large
true bipolar signals which swing below ground to the 0V
to 5V input range of the LTC2364-18. Figure 5a shows the
LT6202 being used to convert a ±10V true bipolar signal
for use by the LTC2364-18. In this case, the LT6202 is
configured as an inverting amplifier stage, which acts to
attenuateandlevelshifttheinputsignaltothe0Vto5Vinput
rangeoftheLTC2364-18.Intheinvertingconfiguration,the
single-ended input signal source no longer directly drives
a high impedance input. The input impedance is instead
set by resistor RIN. RIN must be chosen carefully based on
the source impedance of the signal source. Higher values
of RIN tend to degrade both the noise and distortion of
the LT6202 and LTC2364-18 as a system. Table 1 shows
the resulting SNR and THD for several values of RIN, R1,
R2, R3 and R4 in this configuration. Figure 5b shows the
resultingFFTwhenusingtheLT6202asshowninFigure5a.
Figure 4. Input Signal Chain
Another filter network consisting of LPF2 should be used
between the buffer and ADC input to both minimize the
noisecontributionofthebufferandtohelpminimizedistur-
bances reflected into the buffer from sampling transients.
Long RC time constants at the analog inputs will slow
down the settling of the analog inputs. Therefore, LPF2
requires a wider bandwidth than LPF1. A buffer amplifier
with a low noise density must be selected to minimize
degradation of the SNR.
10
10nF
66nF
50
LPF2
LPF1
BW = 1.6MHz
BW = 48kHz
LTC2364-18
IN+
IN–
236418 F04
–
+
LT6202
VREF
0V
相關PDF資料 |
PDF描述 |
|---|---|
| VI-22N-IW-F3 | CONVERTER MOD DC/DC 18.5V 100W |
| VE-BNM-MW-F1 | CONVERTER MOD DC/DC 10V 100W |
| VE-B53-MY | CONVERTER MOD DC/DC 24V 50W |
| LTC2857HDD-2#TRPBF | IC TXRX RS485/RS422 8-DFN |
| VE-BNL-MW-F4 | CONVERTER MOD DC/DC 28V 100W |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2364IDE-16#PBF | 功能描述:IC ADC 16BIT SPI/SRL 250K 16DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 其它有關文件:TSA1204 View All Specifications 標準包裝:1 系列:- 位數:12 采樣率（每秒）:20M 數據接口:并聯 轉換器數目:2 功率耗散（最大）:155mW 電壓電源:模擬和數字 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:48-TQFP 供應商設備封裝:48-TQFP（7x7） 包裝:Digi-Reel® 輸入數目和類型:4 個單端，單極；2 個差分，單極 產品目錄頁面:1156 (CN2011-ZH PDF) 其它名稱:497-5435-6 |
| LTC2364IDE-16#PBF | 制造商:Linear Technology 功能描述:ADC 16BIT 250KSPS SPI DFN-16 |
| LTC2364IDE-16#TRPBF | 功能描述:IC ADC 16BIT SPI/SRL 250K 16-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| LTC2364IDE-18#PBF | 功能描述:IC ADC 18BIT 250K 1CH 16DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
| LTC2364IDE-18#TRPBF | 功能描述:IC ADC 18BIT 250K 1CH 16DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率（每秒）:83k 數據接口:串行，并聯 轉換器數目:1 功率耗散（最大）:95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP（0.600"，15.24mm） 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。