Figure 11. 32k Point FFT with fIN = 2kHz of the LTC2378-18" />
參數資料
型號: LTC2378CDE-18#PBF
廠商: Linear Technology
文件頁數: 6/24頁
文件大?。?/td> 0K
描述: IC ADC 18BIT 1MSPS 16-DFN
產品培訓模塊: LTC2379- 18-/16-bit Fully-Differential SAR ADC Family Overview
標準包裝: 91
位數: 18
采樣率(每秒): 1M
數據接口: 串行,SPI?
轉換器數目: 1
功率耗散(最大): 15.8mW
電壓電源: 模擬和數字
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 16-WFDFN 裸露焊盤
供應商設備封裝: 16-DFN(4x3)
包裝: 管件
輸入數目和類型: 1 個差分,雙極
配用: DC1783A-F-ND - BOARD SAR ADC LTC2378-18
DC1783A-B-ND - BOARD SAR ADC LTC2378-16
LTC2378-18
14
237818f
Figure 11. 32k Point FFT with fIN = 2kHz of the LTC2378-18
FREQUENCY (kHz)
0
100
200
300
500
400
–180
AMPLITUDE
(dBFS)
–60
–40
–20
–80
–100
–120
–140
–160
0
237818 F11
SNR = 102.3dB
THD = –124dB
SINAD = 102.2dB
SFDR = 126dB
APPLICATIONS INFORMATION
0μA to a maximum of 0.75mA at 1Msps. This step in DC
current draw triggers a transient response in the reference
that must be considered since any deviation in the refer-
ence output voltage will affect the accuracy of the output
code. In applications where the transient response of the
reference is important, the fast settling LTC6655-5 refer-
ence is also recommended.
DYNAMIC PERFORMANCE
Fast Fourier Transform (FFT) techniques are used to test
the ADC’s frequency response, distortion and noise at the
rated throughput. By applying a low distortion sine wave
and analyzing the digital output using an FFT algorithm,
the ADC’s spectral content can be examined for frequen-
cies outside the fundamental. The LTC2378-18 provides
guaranteed tested limits for both AC distortion and noise
measurements.
Signal-to-Noise and Distortion Ratio (SINAD)
The signal-to-noise and distortion ratio (SINAD) is the
ratio between the RMS amplitude of the fundamental input
frequency and the RMS amplitude of all other frequency
components at the A/D output. The output is band-limited
to frequencies from above DC and below half the sampling
frequency. Figure 11 shows that the LTC2378-18 achieves
a typical SINAD of 102dB at a 1MHz sampling rate with
a 2kHz input.
Signal-to-Noise Ratio (SNR)
The signal-to-noise ratio (SNR) is the ratio between the
RMS amplitude of the fundamental input frequency and
the RMS amplitude of all other frequency components
except the first five harmonics and DC. Figure 11 shows
that the LTC2378-18 achieves a typical SNR of 102dB at
a 1MHz sampling rate with a 2kHz input.
Total Harmonic Distortion (THD)
Total Harmonic Distortion (THD) is the ratio of the RMS sum
of all harmonics of the input signal to the fundamental itself.
The out-of-band harmonics alias into the frequency band
between DC and half the sampling frequency (fSMPL/2).
THD is expressed as:
THD
=20log
V2
2 + V32 + V42 +…+ V
N
2
V1
where V1 is the RMS amplitude of the fundamental fre-
quency and V2 through VN aretheamplitudesofthesecond
through Nth harmonics.
POWER CONSIDERATIONS
The LTC2378-18 provides two power supply pins: the
2.5V power supply (VDD), and the digital input/output
interface power supply (OVDD). The flexible OVDD supply
allows the LTC2378-18 to communicate with any digital
logic operating between 1.8V and 5V, including 2.5V and
3.3V systems.
Power Supply Sequencing
The LTC2378-18 does not have any specific power supply
sequencing requirements. Care should be taken to adhere
to the maximum voltage relationships described in the
Absolute Maximum Ratings section. The LTC2378-18
has a power-on-reset (POR) circuit that will reset the
LTC2378-18 at initial power-up or whenever the power
supply voltage drops below 1V. Once the supply voltage
re-enters the nominal supply voltage range, the POR will
reinitialize the ADC. No conversions should be initiated
until 20μs after a POR event to ensure the reinitialization
period has ended. Any conversions initiated before this
time will produce invalid results.
相關PDF資料
PDF描述
LTC488CN IC LINE RCVR RS485 QUAD 16-DIP
LTC487CN IC DVR RS485 LOW PWR QUAD 16-DIP
LTC486CN IC DVR RS485 LOW PWR QUAD 16-DIP
MS27466E11F5S CONN RCPT 5POS WALL MT W/SCKT
MS3100E16-10PW CONN RCPT 3POS WALL MNT W/PINS
相關代理商/技術參數
參數描述
LTC2378CDE-20#PBF 制造商:Linear Technology 功能描述:IC ADC 20BIT 1MSPS 16DFN 制造商:Linear Technology 功能描述:ADC 2.5-5.1V 20BIT 1MSPS SPI 16DFN 制造商:Linear Technology 功能描述:ADC, 2.5-5.1V, 20BIT, 1MSPS, SPI, 16DFN 制造商:Linear Technology 功能描述:MS-ADC/General Purpose, 20-Bit, 1Msps, 104dB SNR, 0.5pmm INL, 21mW, SAR ADC with 制造商:Linear Technology 功能描述:ADC, 20BIT, 1MSPS, SPI, DFN-16, Resolution (Bits):20bit, Sampling Rate:1MSPS, Supply Voltage Type:Single, Supply Voltage Min:2.375V, Supply Voltage Max:2.625V, Supply Current:8.4mA, Digital IC Case Style:DFN, No. of Pins:16 , RoHS Compliant: Yes
LTC2378CDE-20#TRPBF 制造商:Linear Technology 功能描述:IC ADC 20BIT 1MSPS 16DFN 制造商:Linear Technology 功能描述:MS-ADC/General Purpose, 20-Bit, 1Msps, 104dB SNR, 0.5pmm INL, 21mW, SAR ADC with 制造商:Linear Technology 功能描述:ADC, 20BIT, 1MSPS, SPI, DFN-16, Resolution (Bits):20bit, Sampling Rate:1MSPS, Supply Voltage Type:Single, Supply Voltage Min:2.375V, Supply Voltage Max:2.625V, Supply Current:8.4mA, Digital IC Case Style:DFN, No. of Pins:16 , RoHS Compliant: Yes
LTC2378CMS-16#PBF 功能描述:IC ADC 16BIT 1MSPS 16-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率(每秒):1M 數據接口:串行,SPI? 轉換器數目:1 功率耗散(最大):- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤(4x4) 包裝:Digi-Reel® 輸入數目和類型:8 個單端,單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
LTC2378CMS-16#TRPBF 功能描述:IC ADC 16BIT 1MSPS 16-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯(lián) 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極
LTC2378CMS-18#PBF 功能描述:IC ADC 18BIT 1MSPS 16-MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:- 位數:14 采樣率(每秒):83k 數據接口:串行,并聯(lián) 轉換器數目:1 功率耗散(最大):95mW 電壓電源:雙 ± 工作溫度:0°C ~ 70°C 安裝類型:通孔 封裝/外殼:28-DIP(0.600",15.24mm) 供應商設備封裝:28-PDIP 包裝:管件 輸入數目和類型:1 個單端,雙極