參數資料
型號： LTC2411
廠商： Linear Technology Corporation
元件分類： ADC
英文描述： 2.7V to 5.5V Micropower 24-Bit Differential Σ△ Analog to Digital Converter(2.7V ～5.5V，微功耗，24位差分Σ△串行模數轉換器)
中文描述： 2.7V至5.5V微功耗24位差分Σ△模數轉換器（2.7?5.5V的，微功耗，24位差分Σ△串行模數轉換器）
文件頁數： 12/24頁
文件大小： 268K
代理商： LTC2411
LTC2411
12
APPLICATIU
W
U
U
Serial Clock Input/Output (SCK)
The serial clock signal present on SCK (Pin 9) is used to
synchronize the data transfer. Each bit of data is shifted out
the SDO pin on the falling edge of the serial clock.
In the Internal SCK mode of operation, the SCK pin is an
output and the LTC2411 creates its own serial clock by
dividing the internal conversion clock by 8. In the External
SCK mode of operation, the SCK pin is used as input. The
internal or external SCK mode is selected on power-up and
then reselected every time a HIGH-to-LOW transition is
detected at the CS pin. If SCK is HIGH or floating at power-
up or during this transition, the converter enters the inter-
nal SCK mode. If SCK is LOW at power-up or during this
transition, the converter enters the external SCK mode.
Serial Data Output (SDO)
The serial data output pin, SDO (Pin 8), provides the result
of the last conversion as a serial bit stream (MSB first)
during the data output state. In addition, the SDO pin is
used as an end of conversion indicator during the conver-
sion and sleep states.
When CS (Pin 7) is HIGH, the SDO driver is switched to a
high impedance state. This allows sharing the serial
interface with other devices. If CS is LOW during the
convert or sleep state, SDO will output EOC. If CS is LOW
during the conversion phase, the EOC bit appears HIGH on
the SDO pin. Once the conversion is complete, EOC goes
LOW. The device remains in the sleep state until the first
rising edge of SCK occurs while CS = LOW.
Chip Select Input (CS)
The active LOW chip select, CS (Pin 7), is used to test the
conversion status and to enable the data output transfer as
described in the previous sections.
In addition, the CS signal can be used to trigger a new
conversion cycle before the entire serial data transfer has
been completed. The LTC2411 will abort any serial data
transfer in progress and start a new conversion cycle
anytime a LOW-to-HIGH transition is detected at the CS
pin after the converter has entered the data output state
(i.e., after the first rising edge of SCK occurs with
CS=LOW).
Finally, CS can be used to control the free-running modes
of operation, see Serial Interface Timing Modes section.
Grounding CS will force the ADC to continuously convert
at the maximum output rate selected by F
O
.
SERIAL INTERFACE TIMING MODES
The LTC2411’s 3-wire interface is SPI and MICROWIRE
compatible. This interface offers several flexible modes of
operation. These include internal/external serial clock,
2- or 3-wire I/O, single cycle conversion. The following
sections describe each of these serial interface timing
modes in detail. In all these cases, the converter can use
the internal oscillator (F
O
= LOW or F
O
= HIGH) or an
external oscillator connected to the F
O
pin. Refer to Table4
for a summary.
External Serial Clock, Single Cycle Operation
(SPI/MICROWIRE Compatible)
This timing mode uses an external serial clock to shift out
the conversion result and a CS signal to monitor and
control the state of the conversion cycle, see Figure 5.
Table 4. LTC2411 Interface Timing Modes
Conversion
Cycle
Control
CS and SCK
SCK
CS
↓
Continuous
Data
Output
Control
CS and SCK
SCK
CS
↓
Internal
Connection
and
Waveforms
Figures 5, 6
Figure 7
Figures 8, 9
Figure 10
SCK
Source
External
External
Internal
Internal
Configuration
External SCK, Single Cycle Conversion
External SCK, 2-Wire I/O
Internal SCK, Single Cycle Conversion
Internal SCK, 2-Wire I/O, Continuous Conversion
相關PDF資料
PDF描述
LTC2413CGN 24-Bit No Latency ADC, with Simultaneous 50Hz/60Hz Rejection
LTC2413IGN 24-Bit No Latency ADC, with Simultaneous 50Hz/60Hz Rejection
LTC2413 2.7V to 5.5V Simultaneous 50Hz/60Hz Rejection Micropower Differential Σ△ Analog to Digital Converter(2.7V ～5.5V，微功耗，24位差分Σ△串行模數轉換器)
LTC2414CGN 8-/16-Channel 24-Bit No Latency TM ADCs
LTC2414IGN 8-/16-Channel 24-Bit No Latency TM ADCs
相關代理商/技術參數
參數描述
LTC2411-1CMS 功能描述:IC A/DCONV DIFF INPUT&REF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC2411-1CMS#PBF 功能描述:IC A/DCONV DIFF INPUT&REF 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC2411-1CMS#TR 功能描述:IC A/DCONV DIFF INPUT&REF 10MSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC2411-1CMS#TRPBF 功能描述:IC A/DCONV DIFF INPUT&REF 10MSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極
LTC2411-1CMSPBF 制造商:Linear Technology 功能描述:ADC 24-Bit Differential and Ref. MSOP10
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*