- 您現在的位置：買賣IC網 > PDF目錄377769 > LTC2424CG (LINEAR TECHNOLOGY CORP) 16-Bit 2.5-V to 3.3-V/3.3-V To 5-V Level Shifting Transceiver With 3-State Outputs 56-BGA MICROSTAR JUNIOR -40 to 85 PDF資料下載
參數資料
| 型號： | LTC2424CG |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | ADC |
| 英文描述： | 16-Bit 2.5-V to 3.3-V/3.3-V To 5-V Level Shifting Transceiver With 3-State Outputs 56-BGA MICROSTAR JUNIOR -40 to 85 |
| 中文描述： | 4-CH 20-BIT DELTA-SIGMA ADC, SERIAL ACCESS, PDSO28 |
| 封裝： | 0.209 INCH, PLASTIC, SSOP-28 |
| 文件頁數： | 13/36頁 |
| 文件大?。?/td> | 409K |
| 代理商： | LTC2424CG |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
LTC2412
13
2412f
The LTC2412 performs offset and full-scale calibrations
every conversion cycle. This calibration is transparent to
the user and has no effect on the cyclic operation de-
scribed above. The advantage of continuous calibration is
extreme stability of offset and full-scale readings with re-
spect to time, supply voltage change and temperature drift.
Power-Up Sequence
The LTC2412 automatically enters an internal reset state
when the power supply voltage V
CC
drops below approxi-
mately 2V. This feature guarantees the integrity of the
conversion result and of the serial interface mode selec-
tion. (See the 2-wire I/O sections in the Serial Interface
Timing Modes section.)
When the V
CC
voltage rises above this critical threshold,
the converter creates an internal power-on-reset (POR)
signal with a typical duration of 1ms. The POR signal clears
all internal registers and selects channel 0. Following the
POR signal, the LTC2412 starts a normal conversion cycle
and follows the succession of states described above. The
first conversion result following POR is accurate within the
specifications of the device if the power supply voltage is
restored within the operating range (2.7V to 5.5V) before
the end of the POR time interval.
Reference Voltage Range
This converter accepts a truly differential external refer-
ence voltage. The absolute/common mode voltage speci-
fication for the REF
+
and REF
–
pins covers the entire range
from GND to V
CC
. For correct converter operation, the
REF
+
pin must always be more positive than the REF
–
pin.
The LTC2412 can accept a differential reference voltage
from 0.1V to V
CC
. The converter output noise is deter-
mined by the thermal noise of the front-end circuits, and
as such, its value in nanovolts is nearly constant with
reference voltage. A decrease in reference voltage will not
significantly improve the converter’s effective resolution.
On the other hand, a reduced reference voltage will im-
prove the converter’s overall INL performance. A reduced
reference voltage will also improve the converter perfor-
mance when operated with an external conversion clock
(external F
O
signal) at substantially higher output data
rates (see the Output Data Rate section).
Input Voltage Range
The analog input is truly differential with an absolute/
common mode range for the CH0
+
/CH0
–
or CH1
+
/CH1
–
input pins extending from GND – 0.3V to V
CC
+ 0.3V.
Outside these limits, the ESD protection devices begin to
turn on and the errors due to input leakage current
increase rapidly. Within these limits, the LTC2412 con-
verts the bipolar differential input signal, V
IN
= IN
+
– IN
–
,
from –FS = –0.5 V
REF
to +FS = 0.5 V
REF
where V
REF
=
REF
+
– REF
–
, with the selected channel referred as IN
+
and
IN
–
. Outside this range, the converter indicates the
overrange or the underrange condition using distinct
output codes.
Input signals applied to the analog input pins may extend
by 300mV below ground and above V
CC
. In order to limit
any fault current, resistors of up to 5k may be added in
series with the pins without affecting the performance of
the device. In the physical layout, it is important to main-
tain the parasitic capacitance of the connection between
these series resistors and the corresponding pins as low
as possible; therefore, the resistors should be located as
close as practical to the pins. The effect of the series
resistance on the converter accuracy can be evaluated
from the curves presented in the Input Current/Reference
Current sections. In addition, series resistors will intro-
duce a temperature dependent offset error due to the input
leakage current. A 1nA input leakage current will develop
a 1ppm offset error on a 5k resistor if V
REF
= 5V. This error
has a very strong temperature dependency.
Output Data Format
The LTC2412 serial output data stream is 32 bits long. The
first 3 bits represent status information indicating the
conversion state, selected channel and sign. The next 24
bits are the conversion result, MSB first. The remaining 5
bits are sub LSBs beyond the 24-bit level that may be
included in averaging or discarded without loss of resolu-
tion. The third and fourth bit together are also used to
indicate an underrange condition (the differential input
voltage is below –FS) or an overrange condition (the
differential input voltage is above +FS).
APPLICATIU
W
U
U
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2424I | 16-Bit 2.5-V to 3.3-V/3.3-V To 5-V Level Shifting Transceiver With 3-State Outputs 54-BGA MICROSTAR JUNIOR -40 to 85 |
| LTC2424IG | 16-Bit 2.5-V to 3.3-V/3.3-V To 5-V Level Shifting Transceiver With 3-State Outputs 48-TSSOP -40 to 85 |
| LTC2440 | 2-Channel Differential Input 24-Bit No Latency DS ADC |
| LTC2411-1 | 16-Bit Universal Bus Driver With 3-State Outputs 48-TVSOP -40 to 85 |
| LTC2412 | 16-Bit Universal Bus Driver With 3-State Outputs 48-SSOP -40 to 85 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2424CG#PBF | 功能描述:IC ADC 20BIT 4CH MICROPWR 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2424CG#TR | 功能描述:IC ADC 20BIT 4CH MICROPWR 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2424CG#TRPBF | 功能描述:IC ADC 20BIT 4CH MICROPWR 28SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2424CGPBF | 制造商:Linear Technology 功能描述:ADC,LTC2424C 20bit D-S 4 ch SPI SSOP |
| LTC2424IG | 功能描述:IC ADC 20BIT 4CH MICROPWR 28SSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。