DISCK Internal SCK Duty Cycle (" />
參數資料
型號: LTC2446IUHF#TRPBF
廠商: Linear Technology
文件頁數: 24/28頁
文件大?。?/td> 0K
描述: IC ADC 24BIT 8CH HI SPEED 38QFN
標準包裝: 2,500
位數: 24
采樣率(每秒): 8k
數據接口: MICROWIRE?,串行,SPI?
轉換器數目: 1
功率耗散(最大): 40mW
電壓電源: 單電源
工作溫度: -40°C ~ 85°C
安裝類型: 表面貼裝
封裝/外殼: 38-WFQFN 裸露焊盤
供應商設備封裝: 38-QFN(5x7)
包裝: 帶卷 (TR)
輸入數目和類型: 8 個單端,雙極;4 個差分,雙極
配用: DC847A-ND - BOARD DELTA SIGMA ADC LTC2446
LTC2446/LTC2447
5
24467fa
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
DISCK
Internal SCK Duty Cycle
(Note 9)
45
55
%
fESCK
External SCK Frequency Range
(Note 8)
20
MHz
tLESCK
External SCK Low Period
(Note 8)
25
ns
tHESCK
External SCK High Period
(Note 8)
25
ns
tDOUT_ISCK
Internal SCK 32-Bit Data Output Time
Internal Oscillator (Notes 9, 11)
41.6
35.3
30.9
s
External Oscillator (Notes 9, 10)
320/fEOSC
s
tDOUT_ESCK
External SCK 32-Bit Data Output Time
(Note 8)
32/fESCK
s
t1
CS
↓ to SDO Low Z
(Note 12)
025
ns
t2
CS
↑ to SDO High Z
(Note 12)
025
ns
t3
CS
↓ to SCK ↓
(Note 9)
5
s
t4
CS
↓ to SCK ↑
(Notes 8, 12)
25
ns
tKQMAX
SCK
↓ to SDO Valid
25
ns
tKQMIN
SDO Hold After SCK
(Note 5)
15
ns
t5
SCK Setup Before CS
50
ns
t6
SCK Hold After CS
50
ns
t7
SDI Setup Before SCK
(Note 5)
10
ns
t8
SDI Hold After SCK
(Note 5)
10
ns
The
denotes specifications which apply over the full operating temperature
range, otherwise specifications are at TA = 25°C. (Note 3)
TI I G CHARACTERISTICS
W
U
GND (Pins 1, 4, 5, 6, 31, 32, 33): Ground. Multiple
ground pins internally connected for optimum ground
current flow and VCC decoupling. Connect each one of
these pins to a common ground plane through a low
impedance connection. All seven pins must be connected
to ground for proper operation.
BUSY (Pin 2): Conversion in Progress Indicator. This pin
is HIGH while the conversion is in progress and goes LOW
indicating the conversion is complete and data is ready. It
remains LOW during the sleep and data output states. At
the conclusion of the data output state, it goes HIGH
indicating a new conversion has begun.
EXT (Pin 3): Internal/External SCK Selection Pin. This pin
is used to select internal or external SCK for outputting/
inputting data. If EXT is tied low, the device is in the
external SCK mode and data is shifted out of the device
under the control of a user applied serial clock. If EXT is
tied high, the internal serial clock mode is selected. The
device generates its own SCK signal and outputs this on
the SCK pin. A framing signal BUSY (Pin 2) goes low
indicating data is being output.
COM (Pin 7): The common negative input (IN) for all
single ended multiplexer configurations. The voltage on
CH0-CH7 and COM pins can have any value between GND
UU
U
PI FU CTIO S
Note 1: Absolute Maximum Ratings are those values beyond which the life
of the device may be impaired.
Note 2: All voltage values are with respect to GND.
Note 3: VCC = 4.5V to 5.5V unless otherwise specified.
VREF = REF+ – REF, VREFCM = (REF+ + REF)/2; REF+ is the positive
reference input, REFis the negative reference input; VIN = IN
+ – IN,
VINCM = (IN+ + IN)/2.
Note 4: FO pin tied to GND or to external conversion clock source with
fEOSC = 10MHz unless otherwise specified.
Note 5: Guaranteed by design, not subject to test.
Note 6: Integral nonlinearity is defined as the deviation of a code from a
straight line passing through the actual endpoints of the transfer curve.
The deviation is measured from the center of the quantization band.
Note 7: The converter uses the internal oscillator.
Note 8: The converter is in external SCK mode of operation such that the
SCK pin is used as a digital input. The frequency of the clock signal driving
SCK during the data output is fESCK and is expressed in Hz.
Note 9: The converter is in internal SCK mode of operation such that the
SCK pin is used as a digital output. In this mode of operation, the SCK pin
has a total equivalent load capacitance of CLOAD = 20pF.
Note 10: The external oscillator is connected to the FO pin. The external
oscillator frequency, fEOSC, is expressed in Hz.
Note 11: The converter uses the internal oscillator. FO = 0V.
Note 12: Guaranteed by design and test correlation.
Note 13: There is an internal reset that adds an additional 1
s (typ) to the
conversion time.
相關PDF資料
PDF描述
LTC2448IUHF#TRPBF IC ADC 24BIT HI SPEED 38QFN
LTC2451ITS8#TRPBF IC ADC 16BIT DELTA SIG TSOT23-8
LTC2452ITS8#TRPBF IC ADC 16BIT DELTA SIG TSOT23-8
LTC2453ITS8#TRMPBF IC ADC 16BIT DELTA SIG TSOT23-8
LTC2482IDD#TRPBF IC ADC 16BIT 10-DFN
相關代理商/技術參數
參數描述
LTC2447CUHF#PBF 功能描述:IC ADC 24BIT 8CH HI SPEED 38QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
LTC2447CUHF#TRPBF 功能描述:IC ADC 24BIT 8CH HI SPEED 38QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
LTC2447IUHF#PBF 功能描述:IC ADC 24BIT 8CH HI SPEED 38QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率(每秒):1M 數據接口:串行,SPI? 轉換器數目:1 功率耗散(最大):- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤(4x4) 包裝:Digi-Reel® 輸入數目和類型:8 個單端,單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6
LTC2447IUHF#TRPBF 功能描述:IC ADC 24BIT 8CH HI SPEED 38QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極
LTC2448CUHF 功能描述:IC ADC 24BIT HI SPEED 38QFN RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率(每秒):45k 數據接口:串行 轉換器數目:2 功率耗散(最大):315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC(0.295",7.50mm 寬) 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端,單極