- 您現在的位置：買賣IC網 > PDF目錄10365 > LTC2450CDC#TRPBF (Linear Technology)IC ADC 16BIT DELTA SIG 6-DFN PDF資料下載
參數資料
| 型號： | LTC2450CDC#TRPBF |
| 廠商： | Linear Technology |
| 文件頁數： | 6/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC ADC 16BIT DELTA SIG 6-DFN |
| 標準包裝： | 2,500 |
| 位數： | 16 |
| 采樣率（每秒）： | 30 |
| 數據接口： | 串行，SPI? |
| 轉換器數目： | 1 |
| 功率耗散（最大）： | 1.05mW |
| 電壓電源： | 單電源 |
| 工作溫度： | 0°C ~ 70°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 6-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 6-DFN-EP（2x2） |
| 包裝： | 帶卷 (TR) |
| 輸入數目和類型： | 1 個單端，單極 |
| 配用： | DC1067A-B-ND - BOARD DELTA SIGMA ADC LTC2450-1 DC1067A-A-ND - BOARD DELTA SIGMA ADC LTC2450 |
LTC2450
14
2450fb
APPLICATIONS INFORMATION
Digital Signal Levels
The LTC2450’s digital interface is easy to use. Its digital
inputs (SCK and CS) accept standard CMOS logic levels
and the internal hysteresis receivers can tolerate edge
rates as slow as 100μs. However, some considerations
are required to take advantage of the exceptional accuracy
and low supply current of this converter.
The digital output signal SDO is less of a concern because
it is not active during the conversion cycle.
While a digital input signal is in the range 0.5V to VCC
–0.5V, the CMOS input receiver may draw additional
current from the power supply. Due to the nature of CMOS
logic, a slow transition within this voltage range may cause
an increase in the power supply current drawn by the
converter, particularly in the low power operation mode
within the SLEEP state. Thus, for low power consumption
it is highly desirable to provide relatively fast edges for the
two digital input pins SCK and CS, and to keep the digital
input logic levels at VCC or GND.
At the same time, during the CONVERT state, undershoot
and/or overshoot of fast digital signals connected to the
LTC2450 pins may alter the conversion result. Under-
shoot and overshoot can occur because of an impedance
mismatch at the converter pin combined with very fast
transition times. This problem becomes particularly difcult
when shared control lines are used and multiple reec-
tions may occur. The solution is to carefully terminate all
transmission lines close to their characteristic impedance.
Parallel termination is seldom an acceptable option in low
power systems so a series resistor between 27Ω and 56Ω
placed near the driver may eliminate this problem. The
actual resistor value depends upon the trace impedance
and connection topology. An alternate solution is to reduce
the edge rate of the control signals, keeping in mind the
concerns regarding slow edges mentioned above.
Particular attention should be given to congurations in
which a continuous clock signal is applied to SCK pin during
the CONVERT state. While LTC2450 will ignore this signal
from a logic point of view the signal edges may create
unexpected errors depending upon the relation between
its frequency and the internal oscillator frequency. In such
a situation it is benecial to use edge rates of about 10ns
and to limit potential undershoot to less than 0.3V below
GND and overshoot to less than 0.3V above VCC.
Noisy external circuitry can potentially impact the output
under 2-wire operation. In particular, it is possible to get
the LTC2450 into an unknown state if an SCK pulse is
missed or noise triggers an extra SCK pulse. In this situ-
ation, it is impossible to distinguish SDO = 1 (indicating
conversion in progress) from valid “1” data bits. As such,
CPOL = 1 is recommended for the 2-wire mode. The user
should look for SDO = 0 before reading data, and look
for SDO = 1 after reading data. If SDO does not return a
“0” within the maximum conversion time (or return a “1”
after a full data read), generate 16 SCK pulses to force a
new conversion.
Driving VCC and GND
The VCC and GND pins of the LTC2450 converter are
directly connected to the positive and negative reference
voltages, respectively. A simplied equivalent circuit is
shown in Figure 14.
The power supply current passing through the parasitic
layout resistance associated with these common pins will
modify the ADC reference voltage and thus negatively affect
the converter accuracy. It is thus important to keep the
VCC and GND lines quiet, and to connect these supplies
through very low impedance traces.
In relation to the VCC and GND pins, the LTC2450 com-
bines internal high frequency decoupling with damping
Figure 14. LTC2450 Analog Pins Equivalent Circuit
VCC
ILEAK
RSW (TYP)
15k
CEQ (TYP)
0.35pF
INTERNAL SWITCHING FREQUENCY = 4 MHz
RSW (TYP)
15k
RSW (TYP)
15k
VIN
ILEAK
GND
ILEAK
VCC
2450 F14
相關PDF資料 |
PDF描述 |
|---|---|
| MS27473E12F98P | CONN PLUG 10POS STRAIGHT W/PINS |
| VE-2NM-MX-S | CONVERTER MOD DC/DC 10V 75W |
| LTC2360CTS8#TRMPBF | IC ADC 12BIT 100KSPS TSOT23-8 |
| MS27497E12A3S | CONN RCPT 3POS WALL MNT W/SCKT |
| LTC2360CTS8#TRPBF | IC ADC 12BIT 100KSPS TSOT23-8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2450IDC#PBF | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 30sps 16-bit Serial 6-Pin DFN EP 制造商:Linear Technology 功能描述:Bulk 制造商:Linear Technology 功能描述:ADC 16BIT 30SPS SPI DFN-6 制造商:Linear Technology 功能描述:ADC, 16BIT, 30SPS, SPI, DFN-6; Resolution (Bits):16bit; Sampling Rate:30SPS; Supply Voltage Type:Single; Supply Voltage Min:2.7V; Supply Voltage Max:5.5V; Supply Current:350A; Digital IC Case Style:DFN; No. of Pins:6 ;RoHS Compliant: Yes |
| LTC2450IDC#TRMPBF | 功能描述:IC ADC 16BIT DELTA SIG 6-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2450IDC#TRPBF | 功能描述:IC ADC 16BIT DELTA SIG 6-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2450IDC-1#PBF | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 60sps 16-bit Serial 6-Pin DFN EP 制造商:Linear Technology 功能描述:Bulk 制造商:Linear Technology 功能描述:ADC 16BIT DEL SIG 60HZ 6DF 制造商:Linear Technology 功能描述:ADC, 16BIT, 60SPS, SPI, DFN-6; Resolution (Bits):16bit; Sampling Rate:60SPS; Supply Voltage Type:Single; Supply Voltage Min:2.7V; Supply Voltage Max:5.5V; Supply Current:350A; Digital IC Case Style:DFN; No. of Pins:6 ;RoHS Compliant: Yes |
| LTC2450IDC-1#TRMPBF | 功能描述:IC ADC 16BIT DELTA SIG 6-DFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
發(fā)布緊急采購，3分鐘左右您將得到回復。