- 您現在的位置：買賣IC網 > PDF目錄377771 > LTC2495 (Linear Technology Corporation) 16-Bit 8-/16-Channel ツヒ ADC with PGA, Easy Drive and I2C Interface PDF資料下載
參數資料
| 型號： | LTC2495 |
| 廠商： | Linear Technology Corporation |
| 英文描述： | 16-Bit 8-/16-Channel ツヒ ADC with PGA, Easy Drive and I2C Interface |
| 中文描述： | 16位8-/16-ChannelツヒADC，帶PGA巡回賽，輕松驅動和I2C接口 |
| 文件頁數： | 12/32頁 |
| 文件大?。?/td> | 558K |
| 代理商： | LTC2495 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
LTC2495
12
2495f
CONVERTER OPERATION
Converter Operation Cycle
The LTC2495 is a multichannel, low power, delta-sigma,
analog-to-digital converter with a 2-wire, I
2
C interface.
Its operation is made up of four states (see Figure 1).
The converter operating cycle begins with the conver-
sion, followed by the sleep state, and ends with the data
input/output cycle.
Initially, at power-up, the LTC2495 performs a conversion.
Once the conversion is complete, the device enters the
sleep state. While in the sleep state, power consumption is
reduced by two orders of magnitude. The part remains in
the sleep state as long it is not addressed for a read/write
operation. The conversion result is held indefinitely in a
static shift register while the part is in the sleep state.
The device will not acknowledge an external request dur-
ing the conversion state. After a conversion is finished,
the device is ready to accept a read/write request. Once
the LTC2495 is addressed for a read operation, the device
begins outputting the conversion result under the control
of the serial clock (SCL). There is no latency in the conver-
sion result. The data output is 24 bits long and contains a
16-bit plus sign conversion result. Data is updated on the
falling edges of SCL allowing the user to reliably latch data
on the rising edge of SCL. A new conversion is initiated
by a stop condition following a valid write operation or an
incomplete read operation. The conversion automatically
begins at the conclusion of a complete read cycle (all 24
bits read out of the device).
Ease of Use
The LTC2495 data output has no latency, filter settling
delay, or redundant data associated with the conversion
cycle. There is a one-to-one correspondence between the
conversion and the output data. Therefore, multiplexing
multiple analog inputs is straightforward. Each conver-
sion, immediately following a newly selected input or
mode, is valid and accurate to the full specifications of
the device.
The LTC2495 automatically performs offset and full-scale
calibration every conversion cycle independent of the input
channel selected. This calibration is transparent to the user
APPLICATIONS INFORMATION
Figure 1. State Transition Table
and has no effect on the operation cycle described above.
The advantage of continuous calibration is extreme stability
of offset and full-scale readings with respect to time, supply
voltage variation, input channel, and temperature drift.
Easy Drive Input Current Cancellation
The LTC2495 combines a high precision, delta-sigma ADC
with an automatic, differential, input current cancellation
front end. A proprietary front end passive sampling network
transparently removes the differential input current. This
enables external RC networks and high impedance sen-
sors to directly interface to the LTC2495 without external
amplifiers. The remaining common mode input current
is eliminated by either balancing the differential input im-
pedances or setting the common mode input equal to the
common mode reference (see the Automatic Differential
Input Current Cancellation section). This unique architec-
ture does not require on-chip buffers, thereby enabling
signals to swing beyond ground and V
CC
. Moreover, the
CONVERSION
SLEEP
2495 F01
YES
NO
ACKNOWLEDGE
YES
NO
STOP
OR READ
24 BITS
DATA OUTPUT/INPUT
POWER-ON RESET
DEFAULT CONFIGURATION:
IN
+
= CH0, IN
–
= CH1
50Hz/60Hz REJECTION
1X OUTPUT, GAIN = 1
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2495CUHF | 16-Bit 8-/16-Channel ツヒ ADC with PGA, Easy Drive and I2C Interface |
| LTC2495IUHF | 16-Bit 8-/16-Channel ツヒ ADC with PGA, Easy Drive and I2C Interface |
| LTC2600 | Octal 16-/14-/12-Bit Rail-to-Rail DACs in 16-Lead SSOP |
| LTC2600CGN | Octal 16-/14-/12-Bit Rail-to-Rail DACs in 16-Lead SSOP |
| LTC2600IGN | Octal 16-/14-/12-Bit Rail-to-Rail DACs in 16-Lead SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2495CUHF | 制造商:Linear Technology 功能描述:ADC Single Delta-Sigma 15sps 16-bit Serial 38-Pin QFN EP |
| LTC2495CUHF#PBF | 功能描述:IC ADC 16BIT W/PGA 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| LTC2495CUHF#TRPBF | 功能描述:IC ADC 16BIT W/PGA 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:2,500 系列:- 位數:16 采樣率（每秒）:15 數據接口:MICROWIRE?，串行，SPI? 轉換器數目:1 功率耗散（最大）:480µW 電壓電源:單電源 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:38-WFQFN 裸露焊盤 供應商設備封裝:38-QFN（5x7） 包裝:帶卷 (TR) 輸入數目和類型:16 個單端，雙極；8 個差分，雙極 配用:DC1011A-C-ND - BOARD DELTA SIGMA ADC LTC2494 |
| LTC2495IUHF#PBF | 功能描述:IC ADC 16BIT W/PGA 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1 系列:microPOWER™ 位數:8 采樣率（每秒）:1M 數據接口:串行，SPI? 轉換器數目:1 功率耗散（最大）:- 電壓電源:模擬和數字 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:24-VFQFN 裸露焊盤 供應商設備封裝:24-VQFN 裸露焊盤（4x4） 包裝:Digi-Reel® 輸入數目和類型:8 個單端，單極 產品目錄頁面:892 (CN2011-ZH PDF) 其它名稱:296-25851-6 |
| LTC2495IUHF#TRPBF | 功能描述:IC ADC 16BIT W/PGA 38-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
發布緊急采購，3分鐘左右您將得到回復。