- 您現在的位置：買賣IC網 > PDF目錄377771 > LTC2615IGN (LINEAR TECHNOLOGY CORP) Octal 16-/14-/12-Bit Rail-to-Rail DACs in 16-Lead SSOP PDF資料下載
參數資料
| 型號： | LTC2615IGN |
| 廠商： | LINEAR TECHNOLOGY CORP |
| 元件分類： | DAC |
| 英文描述： | Octal 16-/14-/12-Bit Rail-to-Rail DACs in 16-Lead SSOP |
| 中文描述： | SERIAL INPUT LOADING, 9 us SETTLING TIME, 14-BIT DAC, PDSO16 |
| 封裝： | 0.150 INCH, PLASTIC, SSOP-16 |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 317K |
| 代理商： | LTC2615IGN |
13
LTC2605/LTC2615/LTC2625
2605f
DC output impedance is equivalent to load regulation and
may be derived from it by simply calculating a change in
units from LSB/mA to Ohms. The amplifier’s DC output
impedance is 0.020
when driving a load well away from
the rails.
When drawing a load current from either rail, the output
voltage headroom with respect to that rail is limited by the
30
typical channel resistance of the output devices;
e.g., when sinking 1mA, the minimum output voltage =
30
1mA = 30mV. See the graph Headroom at Rails vs
Output Current in the Typical Performance Characteristics
section.
The amplifiers are stable driving capacitive loads of up
to 1000pF.
Board Layout
The excellent load regulation and DC crosstalk perfor-
mance of these devices is achieved in part by keeping
“signal” and “power” grounds separated internally and by
reducing shared internal resistance to just 0.005
.
The GND pin functions both as the node to which the
reference and output voltages are referred and as a return
path for power currents in the device. Because of this,
careful thought should be given to the grounding scheme
and board layout in order to ensure rated performance.
The PC board should have separate areas for the analog
and digital sections of the circuit. This keeps digital signals
away from sensitive analog signals and facilitates the use
of separate digital and analog ground planes which have
minimal capacitive and resistive interaction with each other.
OPERATIOU
Digital and analog ground planes should be joined at only
one point, establishing a system star ground as close to
the device’s ground pin as possible. Ideally, the analog
ground plane should be located on the component side of
the board, and should be allowed to run under the part to
shield it from noise. Analog ground should be a continu-
ous and uninterrupted plane, except for necessary lead
pads and vias, with signal traces on another layer.
The GND pin of the part should be connected to analog
ground. Resistance from the GND pin to system star
ground should be as low as possible. Resistance here will
add directly to the effective DC output impedance of the
device (typically 0.020
), and will degrade DC crosstalk.
Note that the LTC2605/LTC2615/LTC2625 are no more
susceptible to these effects than other parts of their type;
on the contrary, they allow layout-based performance
improvements to shine rather than limiting attainable
performance with excessive internal resistance.
Rail-to-Rail Output Considerations
In any rail-to-rail voltage output device, the output is
limited to voltages within the supply range.
Since the analog outputs of the device cannot go below
ground, they may limit for the lowest codes as shown in
Figure 4b. Similarly, limiting can occur near full scale
when the REF pin is tied to V
CC
. If V
REF
= V
CC
and the DAC
full-scale error (FSE) is positive, the output for the highest
codes limits at V
CC
as shown in Figure 4c. No full-scale
limiting can occur if V
REF
is less than V
CC
– FSE.
Offset and linearity are defined and tested over the region
of the DAC transfer function where no output limiting
can occur.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC2625IGN | Octal 16-/14-/12-Bit Rail-to-Rail DACs in 16-Lead SSOP |
| LTC2625CGN | Octal 16-/14-/12-Bit Rail-to-Rail DACs in 16-Lead SSOP |
| LTC2615IGN-1 | Octal 16-/14-/12-Bit Rail-to-Rail DACs in 16-Lead SSOP |
| LTC2625IGN-1 | Octal 16-/14-/12-Bit Rail-to-Rail DACs in 16-Lead SSOP |
| LTC2615 | Octal 16-/14-/12-Bit Rail-to-Rail DACs in 16-Lead SSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2615IGN#PBF | 功能描述:IC DAC 14BIT R-R OCT 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:1 系列:- 設置時間:4.5µs 位數:12 數據接口:串行，SPI? 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:8-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:8-SOICN 包裝:剪切帶 (CT) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:* 其它名稱:MCP4921T-E/SNCTMCP4921T-E/SNRCTMCP4921T-E/SNRCT-ND |
| LTC2615IGN#TRPBF | 功能描述:IC DAC 14BIT R-R OCT 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| LTC2615IGN-1#PBF | 功能描述:IC DAC 14BIT R-R OCT 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
| LTC2615IGN-1#TRPBF | 功能描述:IC DAC 14BIT R-R OCT 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| LTC2616CDD | 制造商:Linear Technology 功能描述:MS-DAC/Industrial, 14-bit I2C VOUT DAC |
發布緊急采購，3分鐘左右您將得到回復。