- 您現在的位置：買賣IC網 > PDF目錄8684 > LTC2617IDE-1#PBF (Linear Technology)IC DAC 14BIT R-R I2C 12-DFN PDF資料下載
參數資料
| 型號： | LTC2617IDE-1#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 5/20頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC 14BIT R-R I2C 12-DFN |
| 標準包裝： | 91 |
| 設置時間： | 9µs |
| 位數： | 14 |
| 數據接口： | I²C |
| 轉換器數目： | 2 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 780µW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 12-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 12-DFN（4x3） |
| 包裝： | 管件 |
| 輸出數目和類型： | 2 電壓，單極 |
| 采樣率（每秒）： | * |
LTC2607/LTC2617/LTC2627
26071727fa
operation
specifications. For an I2C bus operating in the fast mode,
an active pull-up will be necessary if the bus capacitance is
greater than 200pF. The VCCpowershouldnotberemoved
from the LTC2607/LTC2617/LTC2627 when the I2C bus
is active to avoid loading the I2C bus lines through the
internal ESD protection diodes.
The LTC2607/LTC2617/LTC2627 are receive-only (slave)
devices. The master can write to the LTC2607/LTC2617/
LTC2627.TheLTC2607/LTC2617/LTC2627donotrespond
to a read from the master.
The START (S) and STOP (P) Conditions
When the bus is not in use, both SCL and SDA must be
high. A bus master signals the beginning of a communica-
tion to a slave device by transmitting a START condition. A
START condition is generated by transitioning SDA from
high to low while SCL is high.
When the master has finished communicating with the
slave, it issues a STOP condition. A STOP condition is
generated by transitioning SDA from low to high while
SCL is high. The bus is then free for communication with
another I2C device.
Acknowledge
The Acknowledge signal is used for handshaking between
the master and the slave. An Acknowledge (active LOW)
generated by the slave lets the master know that the lat-
est byte of information was received. The Acknowledge
related clock pulse is generated by the master. The master
releasestheSDAline(HIGH)duringtheAcknowledgeclock
pulse. The slave-receiver must pull down the SDA bus line
during the Acknowledge clock pulse so that it remains a
stable LOW during the HIGH period of this clock pulse.
The LTC2607/LTC2617/LTC2627 respond to a write by a
master in this manner. The LTC2607/LTC2617/LTC2627
do not acknowledge a read (retains SDA HIGH during the
period of the Acknowledge clock pulse).
Chip Address
The state of CA0, CA1 and CA2 decides the slave address
of the part. The pins CA0, CA1 and CA2 can be each set
to any one of three states: VCC, GND or float. This results
Power-On Reset
The LTC2607/LTC2617/LTC2627 clear the outputs to
zero scale when power is first applied, making system
initialization consistent and repeatable. The LTC2607-1/
LTC2617-1/LTC2627-1 set the voltage outputs to midscale
when power is first applied.
For some applications, downstream circuits are active
during DAC power-up, and may be sensitive to nonzero
outputs from the DAC during this time. The LTC2607/
LTC2617/LTC2627 contain circuitry to reduce the power-
on glitch; furthermore, the glitch amplitude can be made
arbitrarily small by reducing the ramp rate of the power
supply. For example, if the power supply is ramped to 5V
in 1ms, the analog outputs rise less than 10mV above
ground (typ) during power-on. See Power-On Reset Glitch
in the Typical Performance Characteristics section.
Power Supply Sequencing
The voltage at REF (Pin 9) should be kept within the range
–0.3V ≤ VREF ≤ VCC + 0.3V (see Absolute Maximum Rat-
ings). Particular care should be taken to observe these
limitsduringpowersupplyturn-onandturn-offsequences,
when the voltage at VCC (Pin 8) is in transition.
Transfer Function
The digital-to-analog transfer function is:
V
k
V
OUT IDEAL
N
REF
REFLO
(
) =
(
)+
2
where k is the decimal equivalent of the binary DAC
input code, N is the resolution and VREF is the voltage at
REF (Pin 6).
Serial Digital Interface
The LTC2607/LTC2617/LTC2627 communicate with a
host using the standard 2-wire I2C interface. The Timing
Diagrams (Figures 1 and 2) show the timing relationship
of the signals on the bus. The two bus lines, SDA and
SCL, must be high when the bus is not in use. External
pull-up resistors or current sources are required on these
lines. The value of these pull-up resistors is dependent
on the power supply and can be obtained from the I2C
相關PDF資料 |
PDF描述 |
|---|---|
| NB6HQ14MMNTXG | IC CLK BUFF MUX 1:4 5GHZ 16-QFN |
| VE-J71-MY | CONVERTER MOD DC/DC 12V 50W |
| VE-J70-MY | CONVERTER MOD DC/DC 5V 50W |
| NB6L56MNTXG | IC MUX 2.5V/3.3V DUAL DIFF 32QFN |
| NB7L585RMNR4G | IC CLK/DATA BUFFER MUX 1:6 32QFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2619CGN#PBF | 功能描述:IC DAC 14BIT R-R QUAD 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
| LTC2619CGN#TRPBF | 功能描述:IC DAC 14BIT R-R QUAD 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散（最大）:55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流，單極；1 電流，雙極 采樣率（每秒）:* |
| LTC2619CGN-1#PBF | 功能描述:IC DAC 14BIT R-R QUAD 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:50 系列:- 設置時間:4µs 位數:12 數據接口:串行 轉換器數目:2 電壓電源:單電源 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:8-TSSOP，8-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:8-uMAX 包裝:管件 輸出數目和類型:2 電壓，單極 采樣率（每秒）:* 產品目錄頁面:1398 (CN2011-ZH PDF) |
| LTC2619CGN-1#TRPBF | 功能描述:IC DAC 14BIT R-R QUAD 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 標準包裝:2,400 系列:- 設置時間:- 位數:18 數據接口:串行 轉換器數目:3 電壓電源:模擬和數字 功率耗散（最大）:- 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:36-TFBGA 供應商設備封裝:36-TFBGA 包裝:帶卷 (TR) 輸出數目和類型:* 采樣率（每秒）:* |
| LTC2619IGN#PBF | 功能描述:IC DAC 14BIT R-R QUAD 16SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散（最大）:100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC（J 形引線） 供應商設備封裝:28-PLCC（11.51x11.51） 包裝:帶卷 (TR) 輸出數目和類型:1 電壓，單極；1 電壓，雙極 采樣率（每秒）:143k |
發布緊急采購，3分鐘左右您將得到回復。