- 您現在的位置：買賣IC網 > PDF目錄8995 > LTC2622IMS8#PBF (Linear Technology)IC DAC 12BIT DUAL R-R VOUT 8MSOP PDF資料下載
參數資料
| 型號： | LTC2622IMS8#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 2/16頁 |
| 文件大小： | 0K |
| 描述： | IC DAC 12BIT DUAL R-R VOUT 8MSOP |
| 標準包裝： | 50 |
| 設置時間： | 7µs |
| 位數： | 12 |
| 數據接口： | 串行 |
| 轉換器數目： | 2 |
| 電壓電源： | 單電源 |
| 功率耗散（最大）： | 6.5mW |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-MSOP |
| 包裝： | 管件 |
| 輸出數目和類型： | 2 電壓，單極 |
| 采樣率（每秒）： | * |
| 產品目錄頁面： | 1351 (CN2011-ZH PDF) |
10
LTC2602/LTC2612/LTC2622
2602fa
OPERATIO
U
Serial Interface
The CS/LD input is level triggered. When this input is taken
low, it acts as a chip-select signal, activating the SDI and
SCK buffers and enabling the input shift register. Data
(SDI input) is transferred at the next 24 rising SCK edges.
The 4-bit command, C3-C0, is loaded first; then the 4-bit
DAC address, A3-A0; and finally the 16-bit data word. The
data word comprises the 16-, 14- or 12-bit input code,
ordered MSB-to-LSB, followed by 0, 2 or 4 don’t-care bits
(LTC2602, LTC2612 and LTC2622 respectively). Data can
only be transferred to the device when the CS/LD signal is
low.The rising edge of CS/LD ends the data transfer and
causes the device to carry out the action specified in the
24-bit input word. The complete sequence is shown in
Figure 2a.
The command (C3-C0) and address (A3-A0) assignments
are shown in Table 1. The first four commands in the table
consist of write and update operations. A write operation
loads a 16-bit data word from the 32-bit shift register into
the input register of the selected DAC, n. An update
operation copies the data word from the input register to
the DAC register. Once copied into the DAC register, the
data word becomes the active 16-, 14- or 12-bit input
code, and is converted to an analog voltage at the DAC
output. The update operation also powers up the selected
DAC if it had been in power-down mode. The data path and
registers are shown in the block diagram.
While the minimum input word is 24 bits, it may optionally
be extended to 32 bits to accommodate microprocessors
which have a minimum word width of 16 bits (2 bytes). To
use the 32-bit word width, 8 don’t-care bits are transferred
to the device first, followed by the 24-bit word as just
described. Figure 2b shows the 32-bit sequence.
Power-Down Mode
For power-constrained applications, power-down mode
can be used to reduce the supply current whenever less
than two outputs are needed. When in power-down, the
buffer amplifiers, bias circuits and reference inputs are
disabled, and draw essentially zero current. The DAC
outputs are put into a high-impedance state, and the
Power-On Reset
The LTC2602/LTC2612/LTC2622 clear the outputs to zero
scale when power is first applied, making system initializa-
tion consistent and repeatable.
For some applications, downstream circuits are active
during DAC power-up, and may be sensitive to nonzero
outputs from the DAC during this time. The LTC2602/
LTC2612/LTC2622 contain circuitry to reduce the power-
on glitch; furthermore, the glitch amplitude can be made
smaller by reducing the ramp rate of the power supply. For
example, if the power supply is ramped to 5V in 1ms, the
analog outputs rise less than 10mV above ground (typ)
during power-on. See Power-On Reset Glitch in the Typi-
cal Performance Characteristics section.
Power Supply Sequencing
The voltage at REF (Pin 4) should be kept within the range
– 0.3V
≤ VREF ≤ VCC + 0.3V (see Absolute Maximum
Ratings). Particular care should be taken to observe these
limits during power supply turn-on and turn-off sequences,
when the voltage at VCC (Pin 6) is in transition.
Transfer Function
The digital-to-analog transfer function is
V
k
V
OUT IDEAL
N
REF
() =
2
where k is the decimal equivalent of the binary DAC input
code, N is the resolution and VREF is the voltage at REF
(Pin 4).
Table 1.
COMMAND*
C3
C2
C1
C0
0000
Write to Input Register n
0001
Update (Power Up) DAC Register n
0010
Write to Input Register n, Update (Power Up) All n
0011
Write to and Update (Power Up) n
0100
Power Down n
1111
No Operation
ADDRESS (n)*
A3
A2
A1
A0
0000
DAC A
0001
DAC B
1111
All DACs
*Command and address codes not shown are reserved and should not be used.
相關PDF資料 |
PDF描述 |
|---|---|
| MS3121E22-55PY | CONN RCPT 55POS CBL MNT W/PINS |
| AD5060ARJZ-1REEL7 | IC DAC 16BIT SPI/SRL SOT23-8 |
| MS3121E22-55P | CONN RCPT 55POS CBL MNT W/PINS |
| MS3456L28-12PY | CONN PLUG 26POS STRAIGHT W/PINS |
| MS3456L28-12PX | CONN PLUG 26POS STRAIGHT W/PINS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC-2623B | 功能描述:LED 顯示器和配件 Blue 4 Dig 0.28" Ht 466nm 3000ucd RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| LTC-2623E | 功能描述:LED 顯示器和配件 4 Digit, Orange RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| LTC-2623G | 功能描述:LED 顯示器和配件 4 Digit, Green RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| LTC-2623JD | 功能描述:LED 顯示器和配件 4 Digit, Red Low Current RoHS:否 制造商:Avago Technologies 顯示器類型:7 Segment 數位數量:2 字符大小:7.8 mm x 14.22 mm 照明顏色:Red 波長:628 nm 共用管腳:Common Anode 工作電壓:2.05 V 工作電流:20 mA 最大工作溫度:+ 85 C 最小工作溫度:- 35 C 封裝:Tube |
| LTC-2623JD-01 | 制造商:Lite-On Semiconductor Corporation 功能描述:DISPLAY,CLOCK,4-DIG,RED,LOW-CUR,0.28",CAMPX - Rail/Tube |
發布緊急采購，3分鐘左右您將得到回復。