參數資料
型號: LTC2704CGW-12#TRPBF
廠商: Linear Technology
文件頁數: 9/22頁
文件大?。?/td> 0K
描述: IC DAC 12BIT QUAD VOUT 44-SSOP
產品培訓模塊: LTC275x 18-Bit DAC
標準包裝: 1,000
設置時間: 8µs
位數: 12
數據接口: 串行,SPI?
轉換器數目: 4
電壓電源: 模擬和數字,雙 ±
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 44-BSOP(0.295",7.50mm 寬)
供應商設備封裝: 44-SSOP
包裝: 帶卷 (TR)
輸出數目和類型: 4 電壓,單極;4 電壓,雙極
采樣率(每秒): *
LTC2704
17
2704fd
APPLICATIONS INFORMATION
Overview
The LTC2704 is a highly integrated device, greatly sim-
plifying design and layout as compared to a design using
multiple current output DACs and separate ampliers. A
similar design using four separate current output DACs
would require six precision op amps, compensation capaci-
tors, bypass capacitors for each amplier, several times as
much PCB area and a more complicated serial interface.
Still, it is important to avoid some common mistakes in
order to achieve full performance. DC752A is the evalu-
ation board for the LTC2704. It is designed to meet all
data sheet specications, and to allow the LTC2704 to be
integrated into other prototype circuitry. All force/sense
lines are available to allow the addition of current booster
stages or other output circuits.
The DC752A design is presented as a tutorial on properly
applying the LTC2704. This board shows how to properly
return digital and analog ground currents, and how to
compensate for small differences in ground potential
between the two banks of two DACs. There are other ways
to ground the LTC2704, but the one requirement is that
analog and digital grounds be connected at the LTC2704
by a very low impedance path. It is NOT advisable to split
the ground planes and connect them with a jumper or
inductor. When in doubt, use a single solid ground plane
rather than separate planes.
The LTC2704 does allow the ground potential of the DACs
to vary by ±300mV with respect to analog ground, allowing
compensation for ground return resistance.
Power Supply Grounding and Noise
LTC2704 V+ and Vpins are the supplies to all of the
output ampliers, ground sense ampliers and reference
inversion ampliers. These ampliers have good power
supply rejection, but the V+ and Vsupplies must be free
from wideband noise. The best scheme is to prelter low
noise regulators such as the LT1761 (positive) and LT1964
(negative). Refer to Linear Technology Application Note
101, Minimizing Switching Regulator Residue in Linear
Regulator Outputs.
The LTC2704 VDD pin is the supply for the digital logic
and analog DAC switches and is very sensitive to noise. It
must be treated as an analog supply. The evaluation board
uses an LT1790 precision reference as the VDD supply to
minimize noise.
The GND pin is the return for digital currents and the
AGND pin is a bias point for internal analog circuitry. Both
of these pins must be tied to the same point on a quiet
ground plane.
Each DAC has a separate ground sense pin that can be used
to compensate for small differences in ground potential
within a system. Since DACs A and B are associated with
REF1 and DACs C and D are associated with REF2, the
grounds must be grouped together as follows:
AGNDA, AGNDB and REFG1 tied together (“GND1” on
DC752A)
AGNDC, AGNDD and REFG2 tied together (“GND2” on
DC752A)
This scheme allows compensation for ground return IR
drops, as long as the resistance is shared by both DACs
in a group. This implies that the ground return for DACs
A and B must be as close as possible, and GND1 must
be connected to this point through a low current, low
resistance trace. (Similar for DACs C and D.)
Figure 3 shows the top layer of the evaluation board. The
GND1 trace connects REFG1, AGNDA, AGNDB and the
ground pin of the LT1236 precision reference (U4.) This
point is the ground reference for DACs A and B. The GND2
trace connects REFG2, AGNDC, AGNDD and the ground pin
of the other LT1236 precision reference (U5). This point
is the ground reference for DACs C and D.
Voltage Reference
A high quality, low noise reference such as the LT1236
or LT1027 must be used to achieve full performance.
The ground terminal of this reference must be connected
directly to the common ground point. If GND1 and GND2
are separate, then two references must be used.
相關PDF資料
PDF描述
AD7537KNZ IC DAC 12BIT DUAL MULT 24DIP
VE-260-IV-F4 CONVERTER MOD DC/DC 5V 150W
VI-B4Y-MW-B1 CONVERTER MOD DC/DC 3.3V 66W
VI-B5D-MU CONVERTER MOD DC/DC 85V 200W
LTC2754ACUKG-16#TRPBF IC DAC 16BIT QUAD IOUT 52-QFN
相關代理商/技術參數
參數描述
LTC2704CGW-14#PBF 功能描述:IC DAC 14BIT QUAD VOUT 44-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散(最大):941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓,單極 采樣率(每秒):*
LTC2704CGW-14#TRPBF 功能描述:IC DAC 14BIT QUAD VOUT 44-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散(最大):100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC(J 形引線) 供應商設備封裝:28-PLCC(11.51x11.51) 包裝:帶卷 (TR) 輸出數目和類型:1 電壓,單極;1 電壓,雙極 采樣率(每秒):143k
LTC2704CGW-16 制造商:Linear Technology 功能描述:DAC 4-CH 16-bit 44-Pin SSOP W
LTC2704CGW-16#PBF 功能描述:IC DAC 16BIT QUAD VOUT 44-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散(最大):941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓,單極 采樣率(每秒):*
LTC2704CGW-16#TRPBF 功能描述:IC DAC 16BIT QUAD VOUT 44-SSOP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1,000 系列:- 設置時間:1µs 位數:8 數據接口:串行 轉換器數目:8 電壓電源:雙 ± 功率耗散(最大):941mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC(0.295",7.50mm 寬) 供應商設備封裝:24-SOIC W 包裝:帶卷 (TR) 輸出數目和類型:8 電壓,單極 采樣率(每秒):*