GEADJA (Pin1): Gain Adjust Pin for DAC A. This control
參數資料
型號: LTC2754BCUKG-16#TRPBF
廠商: Linear Technology
文件頁數: 27/28頁
文件大小: 0K
描述: IC DAC 16BIT QUAD IOUT 52-QFN
標準包裝: 2,000
系列: SoftSpan™
設置時間: 2µs
位數: 16
數據接口: 串行,SPI?
轉換器數目: 4
電壓電源: 單電源
工作溫度: 0°C ~ 70°C
安裝類型: 表面貼裝
封裝/外殼: 52-WFQFN 裸露焊盤
供應商設備封裝: 52-QFN(7x8)裸露焊盤
包裝: 帶卷 (TR)
輸出數目和類型: 8 電流,單極;8 電流,雙極
采樣率(每秒): *
配用: DC1546A-ND - BOARD DAC LTC2754-16
LTC2754
8
2754f
PIN FUNCTIONS
GEADJA (Pin1): Gain Adjust Pin for DAC A. This control
pin can be used to null gain error or to compensate for
reference errors. Nominal adjustment range is ±512 LSB
(LTC2754-16) for a voltage input range of ±VRINA (i.e., ±5V
for a 5V reference input). Tie to ground if not used.
RINA (Pin 2): Input Resistor for Reference Inverting
Amplier. The 20k input resistor is connected internally
from RINA to RCOMA. For normal operation tie RINA to the
external reference voltage VREFA(seeTypicalApplications).
Any or all of these precision-matched resistor sets (Each
set comprising RINX, RCOMX and REFX) may be used to
invert one or more positive reference voltages to the nega-
tive voltages needed by the DACs. Typically 5V; accepts
up to ±15V.
IOUT2A (Pin 3): DAC A Current Output Complement. Tie
IOUT2A to ground.
GND (Pin 4): Ground; provides shielding for IOUT2A. Tie
to ground.
CS/LD (Pin 5): Synchronous Chip Select and Load Pin.
SDI (Pin 6): Serial Data Input. Data is clocked in on the
rising edge of the serial clock (SCK) when CS/LD is low.
SCK (Pin 7): Serial Clock.
SRO (Pin 8): Serial Readback Output. Data is clocked out
on the falling edge of SCK. Readback data begins clocking
out after the last address bit A0 is clocked in. SRO is an
active output only when the chip is selected (i.e., when
CS/LD is low). Otherwise SRO presents a high-impedance
output in order to allow other parts to control the bus.
SROGND (Pin 9): Ground pin for SRO. Tie to ground.
VDD (Pin 10): Positive Supply Input; 2.7V ≤ VDD ≤ 5.5V. By-
pass with a 0.1μF low-ESR ceramic capacitor to ground.
GND (Pin 11): Ground. Tie to ground.
IOUT2D (Pin 12): DAC D Current Output Complement. Tie
IOUT2D to ground.
RIND (Pin 13): Input Resistor for Reference Inverting
Amplier. The 20k input resistor is connected inter-
nally from RIND to RCOMD. For normal operation tie RIND
to the external reference voltage VREFD (see Typical
Applications). Any or all of these precision-matched resis-
tor sets (Each set comprising RINX, RCOMX and REFX) may
be used to invert one or more positive reference voltages
to the negative voltages needed by the DACs. Typically
5V; accepts up to ±15V.
GEADJD (Pin 14): Gain Adjust Pin for DAC D. This control
pin can be used to null gain error or to compensate for
reference errors. Nominal adjustment range is ±512 LSB
(LTC2754-16) for a voltage input range of ±VRIND (i.e., ±5V
for a 5V reference input). Tie to ground if not used.
RCOMD (Pin 15): Center Tap Point for Reference Amplier
Inverting Resistors. The 20k reference inverting resistors
are connected internally from RIND to RCOMD and from
RCOMD to REFD, respectively (see Block Diagram). For
normal operation tie RCOMDtothenegativeinputofexternal
reference inverting amplier (see Typical Applications).
REFD (Pin 16): Inverted Reference Voltage for DAC D, with
internal connection to the reference inverting resistor. The
20k resistor is connected internally from REFD to RCOMD.
For normal operation tie this pin to the output of reference
inverting amplier (see Typical Applications). Typically –5V;
accepts up to ±15V. The impedance looking into this pin
is 10k to ground (RIND and RCOMD oating).
ROFSD (Pin 17): Bipolar Offset Network for DAC D. This
pin provides the translation of the output voltage range for
bipolar spans. Accepts up to ±15V; for normal operation
tie to the positive reference voltage at RIND (Pin 13). The
impedance looking into this pin is 20k to ground.
RFBD (Pin 18): DAC D Feedback Resistor. For normal
operation tie to the output of the I/V converter amplier
for DAC D (see Typical Applications). The DAC output
current from IOUT1D ows through the feedback resistor
to the RFBD pin. The impedance looking into this pin is
10k to ground.
IOUT1D (Pin 19): DAC D Current Output. This pin is a
virtual ground when the DAC is operating and should
reside at 0V. For normal operation tie to the negative
input of the I/V converter amplier for DAC D (see Typi-
cal Applications).
相關PDF資料
PDF描述
VI-B4X-MU CONVERTER MOD DC/DC 5.2V 200W
VI-21V-IV-F1 CONVERTER MOD DC/DC 5.8V 150W
VI-B40-MU CONVERTER MOD DC/DC 5V 200W
VE-240-IV-F4 CONVERTER MOD DC/DC 5V 150W
VE-BNH-MU CONVERTER MOD DC/DC 52V 200W
相關代理商/技術參數
參數描述
LTC2754BIUKG-16#PBF 功能描述:IC DAC 16BIT QUAD IOUT 52-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:SoftSpan™ 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散(最大):100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC(J 形引線) 供應商設備封裝:28-PLCC(11.51x11.51) 包裝:帶卷 (TR) 輸出數目和類型:1 電壓,單極;1 電壓,雙極 采樣率(每秒):143k
LTC2754BIUKG-16#TRPBF 功能描述:IC DAC 16BIT QUAD IOUT 52-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:SoftSpan™ 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散(最大):100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC(J 形引線) 供應商設備封裝:28-PLCC(11.51x11.51) 包裝:帶卷 (TR) 輸出數目和類型:1 電壓,單極;1 電壓,雙極 采樣率(每秒):143k
LTC2754CUKG-12#PBF 功能描述:IC DAC 12BIT QUAD IOUT 52-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:SoftSpan™ 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散(最大):100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC(J 形引線) 供應商設備封裝:28-PLCC(11.51x11.51) 包裝:帶卷 (TR) 輸出數目和類型:1 電壓,單極;1 電壓,雙極 采樣率(每秒):143k
LTC2754CUKG-12#TRPBF 功能描述:IC DAC 12BIT QUAD IOUT 52-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:SoftSpan™ 標準包裝:47 系列:- 設置時間:2µs 位數:14 數據接口:并聯 轉換器數目:1 電壓電源:單電源 功率耗散(最大):55µW 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:28-SSOP(0.209",5.30mm 寬) 供應商設備封裝:28-SSOP 包裝:管件 輸出數目和類型:1 電流,單極;1 電流,雙極 采樣率(每秒):*
LTC2754IUKG-12#PBF 功能描述:IC DAC 12BIT QUAD IOUT 52-QFN RoHS:是 類別:集成電路 (IC) >> 數據采集 - 數模轉換器 系列:SoftSpan™ 產品培訓模塊:Data Converter Fundamentals DAC Architectures 標準包裝:750 系列:- 設置時間:7µs 位數:16 數據接口:并聯 轉換器數目:1 電壓電源:雙 ± 功率耗散(最大):100mW 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-LCC(J 形引線) 供應商設備封裝:28-PLCC(11.51x11.51) 包裝:帶卷 (TR) 輸出數目和類型:1 電壓,單極;1 電壓,雙極 采樣率(每秒):143k