- 您現在的位置：買賣IC網 > PDF目錄10002 > LTC2846CG#TR (Linear Technology)IC TXRX 3.3V MULTIPROTCOL 36SSOP PDF資料下載
參數資料
| 型號： | LTC2846CG#TR |
| 廠商： | Linear Technology |
| 文件頁數： | 9/24頁 |
| 文件大小： | 0K |
| 描述： | IC TXRX 3.3V MULTIPROTCOL 36SSOP |
| 標準包裝： | 2,000 |
| 類型： | 收發器 |
| 驅動器/接收器數： | 3/3 |
| 規程： | 多協議 |
| 電源電壓： | 3.3V |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 36-SSOP（0.209"，5.30mm 寬） |
| 供應商設備封裝： | 36-SSOP |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | LTC2846CGTR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁
17
LTC2846
sn2846 2846fs
A port with one DB-25 connector, that can be configured
for either DTE or DCE operation is shown in Figure 33. The
configuration requires separate cables for proper signal
routing in DTE or DCE operation. For example, in DTE
mode, the TXD signal is routed to Pins 2 and 14 via the
LTC2846’s Driver 1. In DCE mode, Driver 1 now routes the
RXD signal to Pins 2 and 14.
Multiprotocol Interface with RL, LL, TM
and a DB-25 Connector
If the RL, LL and TM signals are implemented, there are not
enough drivers and receivers available in the LTC2846/
LTC2844. In Figure 34, the required control signals are
handled by the LTC2845. The LTC2845 has an additional
single-ended driver/receiver pair that can handle two more
optional control signals such as TM and RL.
Cable-Selectable Multiprotocol Interface
A cable-selectable multiprotocol DTE/DCE interface is
shown in Figure 35. The select lines M0, M1 and DCE/DTE
are brought out to the connector. The mode is selected by
the cable by wiring M0 (connector Pin 18) and M1 (con-
nector Pin 21) and DCE/DTE (connector Pin 25) to ground
(connector Pin 7) or letting them float. If M0, M1 or
DCE/DTE is floating, internal pull-up current sources will
pull the signals to VIN. The select bit M2 is floating, and
therefore, internally pulled high. When the cable is pulled
out, the interface will go into the no-cable mode.
Power Dissipation Calculations
The LTC2846 takes in a 3.3V supply and produces a 5V VCC
with an internal switcher at approximately 80% efficiency.
VDD and VEE are in turn produced from VCC with an internal
charge pump at approximately 80% and 70% efficiency
respectively. Current drawn internally from VDD or VEE
translates directly into a higher ICC. The LTC2846 dissi-
pates power according to the equation:
PDISS(2846) = 125% (VCC ICC)
– ND PRT + NR PRT
(1)
TYPICAL APPLICATIO S
U
PRT refers to the power dissipated by each driver in a
receiver termination on the far end of the cable while ND is
the number of drivers. Conversely, current from the far
end drivers dissipate power NR PRT in the internal
receiver termination where NR is the number of receivers.
LTC2846 Power Dissipation
Consider an LTC2846 in X.21, DCE mode (three V.11
drivers and two V.11 receivers). From the Electrical Char-
acteristics Table, ICC at no load = 14mA, ICC at full load =
100mA. Each receiver termination is 100
(RRT) and
current going into each receiver termination = (100mA –
14mA)/3 = 28.7mA (IRT).
PRT = (IRT)2 RRT
(2)
From Equation (2), PRT = 82.4mW and from Equation (1),
DC power dissipation PDISS(2846) = 125% (5V 100mA)
– 3 82.4mW + 2 82.4mW = 543mW.
Consider the above example running at a baud rate of
10MBd. From the Typical Characteristic for “V.11 Mode
ICC vs Data Rate,” the ICC at 10MBd is 160mA. ICC
increases with baud rate due to driver transient dissipa-
tion. From Equation (1), AC power dissipation PDISS(2846)
= 125% (5V 160mA) –3 82.4mW + 2 82.4mW =
918mW.
LTC2845 Power Dissipation
If a LTC2845 is used to form a complete DCE port with the
LTC2846, it will be running in the X.21 mode (three V.11
drivers and two V.10 drivers, two V.11 receivers and two
V.10 receivers, all with internal 30k termination). In addi-
tion to VCC, it uses the VDD and VEE outputs from the
LTC2846. Negligible power is dissipated in the large
internal receiver termination of the LTC2845 so the NR
PRT term of Equation (1) can be omitted. Thus Equation (1)
is modified as follows:
PDISS(2845) = (VCC ICC) + (VDD IDD)
相關PDF資料 |
PDF描述 |
|---|---|
| VI-B4W-MX-B1 | CONVERTER MOD DC/DC 5.5V 75W |
| VE-BNF-MX-B1 | CONVERTER MOD DC/DC 72V 75W |
| LTC2846CG | IC TXRX 3.3V MULTIPROTCOL 36SSOP |
| IDT72V261LA15TFI8 | IC FIFO SS 8192X18 15NS 64QFP |
| MS27505E19A35S | CONN RCPT 66POS BOX MNT W/SCKT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC2846IG | 功能描述:IC TXRX 3.3V MULTIPROTCOL 36SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| LTC2846IG#PBF | 功能描述:IC TXRX 3.3V MULTIPROTCOL 36SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 產品培訓模塊:RS-232 & USB Transceiver 標準包裝:2,000 系列:- 類型:收發器 驅動器/接收器數:1/1 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-SSOP（0.209"，5.30mm 寬） 供應商設備封裝:16-SSOP 包裝:帶卷 (TR) 其它名稱:296-19849-2 |
| LTC2846IG#TR | 功能描述:IC TXRX 3.3V MULTIPROTCOL 36SSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| LTC2846IG#TRPBF | 功能描述:IC TXRX 3.3V MULTIPROTCOL 36SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
| LTC2847CUHF | 功能描述:IC TXRX MULTIPROTOCOL 38-QFN RoHS:否 類別:集成電路 (IC) >> 接口 - 驅動器，接收器，收發器 系列:- 標準包裝:250 系列:- 類型:收發器 驅動器/接收器數:2/2 規程:RS232 電源電壓:3 V ~ 5.5 V 安裝類型:表面貼裝 封裝/外殼:16-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:16-TSSOP 包裝:帶卷 (TR) |
發布緊急采購，3分鐘左右您將得到回復。